Headlight Fits Sierra

So I’ve had 3 sets of lights on my 11 Sierra HD. The first one was similar to these but with a led strip in the center I liked those but they were sun faded and did not want to restore and the chips in the center were going out the 2nd were Accani absolute trash loved the halo accents that boarded the housing but had blind spots, didn’t adjust and did not run factory size bulbs. So these are the 3rd set and I love them runs OE size in the housing so I dropped in my beamtechs and they adjusted with no problems. Slight moisture in one light no biggie just use clear sealant. Sturdy plastic construction not flimsy like the Acanni ones. Classic look don’t got to worry about accent leds or halos flickering in the assembly or worry about them going out.

Only have one put in so far today and I love the way they look. I also bought LED BULBS for them. Wow what a difference.

I've bought aftermarket lights for an old 97 K1500 Silverado I had, so I didn't have super high expectations for high quality. My 05 Yukon's original headlights were not to bad, but the turn/side marker lenses were hazed over. I was going to install this new set on it, and swap the original headlights to my older 02 Sierra which were far worse. Opening the box, these housings actually look pretty descent. The headlight bracket was pretty flimsy, but that seems pretty standard with aftermarket lights. The GM GMT800 trucks lights are extremely easy to swap. You turn 2 retaining rods a quarter turn and pull them straight up. Then the headlight then just pulls out. The turn/side marker housing has a tab and 2 studs that slide into a cutouts on the truck, and a locking tab on the outside. So this job should have been very quick swap. Installing the low beam bulbs, they would not fully seat into the housing opening. The cutout for the smaller of the 3 tabs was clocked wrong. I slightly shaved the bulbs tab to allow it to insert fully, and then was able to lock them in. When installing the side makers, it seemed the 2 plastic studs on the inner side were to long. To get the inside tab to slide in the truck, it seemed to apply to much pressure causing the outer side of the housing to want to pop out. So when you tried to lock the other side in it would pop out from the tension. There was little give in the plastic at all for the locking clip, so it wouldn't expand fully when inserted and hold the outer side of the housing in place. Coupled with the high tension on the inside the light wouldn't stay in. Trying to install the headlights, the cheap flimsy bracket was warped, not allowing the rods to drop in fully. Thinking there was possibly something misaligned on the truck, I swapped the original lights on both trucks with each other. No problems, done in not even 5 mins. I ended up purchasing a set of TYC CAPA Cert housings for about $35 more that have a far better fit. The headlight bracket isn't as flimsy, so it looks like the housing won't shake while driving down the street.

easy install materials a re good. But it just started getting cold here and already has fogging inside. otherwise good purchase and looks good on my storm trooper truck

I have installed a fair share of aftermarket headlight assemblies, I knew it was a risk that they would get condensation. These are no exception. About 2 weeks after installing them, I took the truck through a automatic wash and one of the lamps started to condensate. I picked up a tube of flowable silicon and ran a bead around the plastic weld of the lamp. I still give these a higher rating because they did think ahead and allow a mesh covering for condensation. So once I ran the silicon around the entire plastic weld, I reinstalled the lamp and took to it with a hair dryer to get the condensation out and it worked very well. This is very common in aftermarket lamps, every set I have ever installed has done this. I knew it was likely so I just advise to save yourself the frustration and get some Flowable Silicone and run a bead around the clear front and back. Other than that these lamps look great and are holding up nicely.

Fits pretty good and looks good

2006 GMC 2500HD SLT So, everything looked good in the beginning, however the lower light housing (parking/turn signal) fits but is loose, didn't "clip" in like the factory OEM housing. I actually broke inside plastic clip on the drivers side when I pushed it in the "clip it" in. The came the headlight housing had two major issues. 1. Build installation, instead of properly space thicker plastic lock rings it has cheap thin metal lock rings that were bent I. Some areas and actually had to be loosened to allow the build to "twist lock" into place..... Not easy getting a screwdriver in to loosen the screws. Once I finally got them on I will say they are bright, especially since I went to LED's 2. Headlight housing install, very bad fit. I could only get the inside lock pin installed on each side. Neither of the outer lock pins would go down all the way, got them on the top but couldn't get the bottom to align. Going to try again when not so pissed off after an hour installing something that honestly should have taken 20min. I kept my Factory OEM headlights on case these vibrate/move too much and I have to take them out and return them. I had such high hopes for these!!

good product fits great on 2003 gmc sierra 2500 arrived quickly product complete drivers upper and lower and pass upper and lower set. nice upgrade and for safety i would recommend

They are full of condensation. Can’t seem to get through the process to exchange them am very disappointed

Had to zip tie not the best but not the worst

BE CAREFUL WITH THIS BUSINESS. Headlights look amazing, not at bright at I thought they would be. Very easy installation plug n play, took me 20 mins to install on my 2012 gmc sierra 1500 Nevada edition. Went to the car wash the next day and the driver side headlight has moisture in it, they say they have vents to control it, I doubt it. Will definitely be taking my business else where.

Fit perfect , easy install , even better clarity then factory, my leds seem to be 1000% brighter