TAILONZ PNEUMATICBlue 1/2 Inch od 32 Meter 100ft PU Air Tubing Kit Pipe Hose Air Line Tubing Or Fluid Transfer Pneumatic tubing

This is pretty impressive. I use it alot and am happy with the results. For a large garage it needs more ends (only has 2)and maybe some instructions. But its fairly intuitive to install. Would recommend.

This is a great complete kit to run airlines throughout the garage or workshop. I added the airline to multiple locations in the garage and a connection point on the ceiling above the roof of the jeep. Allows me to connect to multiple airline locations and run pneumatic nail guns from anywhere in the garage. The kit is very simple to use and has everything you need to get up and operational in a short amount of time

I was able to set my system up in a single day with no leaks. The flexible pneumatic tubing is the best way I've seen (cost, value & safety) to install a compressed air system. I've mentioned safety because too many people have used rigid PVC pipe for their systems. PVC has a nasty habit of shattering while being struck while under pressure sending plastic shrapnel everywhere. The flexible tubing and fittings are the best and convenient way to set up your system quickly. Use the provided tubing cutter to give a good square cut that is necessary for leak-free junction.I have only three issues with this product:1. They only provide two ball valves. I had to purchase another ball valve so I could have one for each manifold. The valves are necessary to drain water that accumulates in the system.2. They only provide six tube clamps. That's simply not enough. You'll need to purchase a package of 1/2" tube clamps to adequately secure the tubing.3. The teflon tape they provide is thin and won't seal well. It would be wise to purchase a spool of teflon tape from Amazon or at your local hardware store.

Great value in this kit. Thanks to smooth pipe interior and the minimal number of fittings needed to route the tube over a long path, this 1/2" system flows a decent scfm. I wouldn't choose it for running a large impact or similar air hog but for basic inflation needs, running an air nailer, using a blow gun etc this is a great system for distributing air around your shop. My only gripe is that the tube is pretty well set in the coil shape it was shipped. Very difficult to get it to relax so you can make nice neat looking runs. Maybe a 90 degree day would help but at 30f it is stiff and ornery. Even exposing the tube to a potent radiant heat source had little effect against the seemingly permanent coil shape. The kit comes with a couple of clips intended to secure the tube but they have nowhere near the holding power that is needed, nor are there anywhere near enough in the kit. Unfortunately Amazon doesn't seem to offer a quality cable clamp that fits this tube at an affordable price. The tube is right on 1/2" od. Affordable clamps marketed as 1/2" are actually less than 3/8. Ones that actually fit are crazy pricey. Give some thought to how you want to secure this tubing and bake the substantial costs into your calculations when considering this kit.

Great hose system for shop or garage. Also great service from TAILONZ one of the items in the kit came incorrectly packaged the 4 Tee's were 3/8" not the 1/2" size I ordered. I contacted TAILONZ and they immediately shipped to me at no charge and no questions asked replacements and they arrived in only days. I have installed this system in my shop and it works great. The only thing I added was better 1/2" hose hangers instead of using the hose clips provided in the kit other wise everything worked perfectly. The hose hangers in the kit are push on and there are only 4 so I ordered 30 - 1/2" stainless steel rubber coated cable clamps and used them to hang the hose on each ceiling joists plus the studs in the walls to hold the hose securely in place. I provided my own 1/4" NTP type T quick couplers to the provided air blocks and the blocks mounted securely to the walls. All that said I'm very happy with this purchase. The push fitting worked great with the provided hose, however the hose is very stiff but I expected that as I had used this type of hose in the past.

For $70, this is quite a value. I've just installed this so I can't speak to longevity just yet. Installation was easy and straight forward even though there are no instructions. Make sure your threaded fittings are taped and tight, tubing cuts are straight and ends fully pushed in, and you should have no leaks. For a hobbyist's shop, this will do just fine.If I were to question any part of this kit, it would be the clamps. The screws are tiny and hard to use and I do question their ability to stay over the long haul. I will probably invest in some electrical harness clamps in the future. All other parts provided feel and appear robust.

When I turned on the air I had a few leaks, no biggy just adjust the fittings. One of the T-Fittings would not stop leaking so I changed it out with a different one. When I turned the air back on that t-fitting literally exploded. My air compressor runs at 130 psi. I bought the black nylon kit because the ratings were higher at Burst Pressure 913Psi, Working Pressure 362Psi. Now I am very leary about using this kit and will definitely be turning the air off when I leave the shop which I have never had to do before.**Update**I contacted the company and they sent me a box of 10 T-fittings. They also said the line is rated at 362psi but the fittings are only rated at 145psi. Doesn't make much sense. Still upping my rating from 1 to 3 stars because customer service was pretty good.

This kit worked out ok for me , it was a good price. but I bought more fittings and hose and manifold blocks.Another time I would just by the hose and fitting separately , this Amazon brand is good quality.I did not use corner fittings , I tried to make as few connections as possible to Minimize leaks. Get your own quality Teflon tape and tighten fitting hard.Manifold blocks have to be drilled out a little to use screws , I’m not using the nails they provide !

I bought whole set but got two pieces outlets one piece missing. the push in connector 1/2 size on other side only 3/8. The outlet cost $15.