EZDIY-FAB GPU VGA PCIe 6 Pin U Turn 180 Degree Angle Connector Power Adapter Board for Desktop Graphics Card-Standard+Reverse Type 2-Pack

My latest PC build, I have been going for a clean install, with minimal cables visible. Leave it up to the video card to toss a wrench in the plan... My card has twin 6-pin plugs for auxiliary power, of course facing straight off the "top" of the card toward to side of the case. I had tried several different wiring tactics to best "de-ugly" the pair of PCI-E cables going to the middle of my build. But no matter what I tried, it was still fugly. THEN I found these 6-pin PCI-E cable adapters designed for video cards. They come as a pair, one piece of each made to flip the cable "up" and over the card (marked "STD"), and one to send it down and under (marked RVS for reverse). My GPU, being a dual-slot card, needed the STD version. But my card also has TWO 6-pin plugs, so I needed TWO of the STD adapters, meaning I had to buy TWO of these sets - so make sure you plan and order correctly. These 180-degree adapters did exactly what I needed them to do - cleanly get the cables going back toward the motherboard. And I had bought some nice PCI-E extension cables to complete clean and subtle look. The adapters are plastic, but have a clean looking beveled "cap" on then, so they look great in my system. They plug in securely with no issues. Once plugged in, there’s about 5mm of clearance over the back of the GPU card, so if you have a backplate, you’ll have room, though not for a really thick one. RECOMMENDED!

Great quality for the price, and they look good in general. I purchased this to use along with a set of 8-pin PCIe U-turn standard plugs that I had purchased previously from this company. I needed to use one of each, as my RTX 2070Super requires an 8-pin and a 6-pin.

Purchased these for a Lenovo M920t that seems to be "anti-gamer PC". Almost every aspect of this tower prevents you from making it a gaming PC. Custom power supply, shallow front to back tower, drive tray hits 6 pin PCI-E power adapter. Set includes two adapters depending on which way your power socket is on your graphics card. One hit the fan shroud of a GTX 1650. The other one made it over the back, but hit a portion of the case. This really isn't the connectors fault. If they were L shaped vs U shaped it would've worked. The downside to the design is there is no retaining clip, so they can just fall out of the power socket. Besides that they appear to be of decent quality, but didn't work for my situation.

It should work with most gaming Nvidia cards and Radeon cards. The cable was routed behind (closer to CPU) and then I attached this firmly to cable. Finally, I firmly attached to the graphics card. No issue with heat building up on connector. Full power delivered. I think it is worth doing just to prevent the cable from bending so much just to make a connection to the graphics card.

Best thing you can do. This and a 90 turn for your 24-pin ATX and you're looking sharp and clean!

The EVGA RTX 2070 graphics card in my primary PC requires two power connectors, a 6-pin and an 8-pin. Bending the wires to connect without adding too much stress to the card, plus routing the cables back to the PSU has always been a pain. When I found a SFF (small form factor) build video on YouTube that used these adapters I ordered them immediately. They connect easily, and the connection to the power cables has a positive click to ensure they're seated. Routing the cables is much easier, and there's no sharp bends required, the cables are straight into the adapter. These are available in both 6-pin and 8-pin versions - the 6-pin adapters have both a standard and a reversed connector in the package. The 8-pin adapters have two of the same orientation in the package, so make sure which ones you need - the pictures clearly show which way the pins are facing, so you can determin the right option(s) for your graphics card. I don't review many purchases, but wanted to note how useful these EZDIY-FAB adapters really are, and how much value they provide for their cost. I'm truly suprised video card manufacturers don't include these in their packaged accessories, they are that useful. Super great product, I'm going to buy these for every PC I work on going forward.

good(?): included U-turn pieces for both possible orientations (this is hard to determine from photos). these pieces have a polarity so that you can't plug any cables in backwards; having a U-turn in each direction is useful for a single installation (might be bad if you want two of the exact same one). bad: ... it didn't actually seem to conduct power at all? the circuit board I was powering only worked when this wasn't installed. is this supposed to be functional? it's not. returned it. maybe it's a fluke idk

Makes the inside of my PC case look so much cleaner. Had some leftover modeling decals so I decorated it! lol

Used in BitFenix Prodigy M when mounting card vertically

Great quality dose exactly what is intended for.

Plugged into card and cables fitted a lot better inside case

Just what I needed perfect fit