HQMasterCNC Router Bits 1/8" Shank CNC Bit End Mill Flat Nose Carbide Endmill Two Flute Spiral Upcut Milling Cutter Tool Set for Wood PVC MDF Hardwood 10Pcs (3.175mm, Total Length: 50mm)

Nice bits, sharp, cut well, seem to be holding up. Only problem I have with them is slipping out of collet. To keep them from slipping I had to roughen up the shank with a diamond stone.

They were packaged well and they functioned. I used them put a slot in a very hard piece of Oak.

Looks like a quality product that will do the job for a long time. Very sharp, watch your fingers.

Cheap on price good durability

Edit #2: It has been almost a year since I purchased 60 bits - I was able to make the bits last but I went through a lot of bits before I had it figured out. I have now changed the review to 3 stars from 1 star. I use these bits to cut cast acrylic. Instead of doing multiple passes, I ended up going with a very slow single pass. I would then do a fast final clean up pass.My settings for 0.4" thick acrylic: Ramp in, 6 IPM plunge (Z-axis), 12 IPM cutting speed, 18,500 RPM. Final pass: 15 IPM plunge, 30 IPM cutting speed, 15,000 RPM.Doing it as 1 pass + 1 fast clean up pass actually cut down my machining time by quite a lot. I'm thankful for that but it makes me wonder what I could have done with the original bits in terms of machining time. I'm going to buy a couple more and see how they fare. I think that the single pass helps with the deflection since it isn't cutting only at the tip. The deflection was probably what was causing the bits to break so fast. With the above settings I use the bit for about 2 hours, then switch to a new bit with a new job. Doing it this way I didn't have any bits that broke in the middle of a job. I might use old bits if I don't care too much about surface finish and just need something cut to rough size. We'll see if the bits I'm about to order work with my new expectations.- old review below -Edit: Changed to 1 star out of frustration with trying to use these bits - gone through 20+ bits so far, for the old version bits I would be on my 2nd or 3rd bit. Original review below.I've been using these bits to cut through ~0.4" thick cast acrylic using a CNC router. They worked well until I needed to get more bits - they changed/simplified the cutter geometry recently. The change in geometry seems to have made the actual thickness of the bit material thinner if that makes sense. There isn't a visible "edge", instead it looks more like "cones".I did have some of the previous bits break but typically the bit would break because they had gotten dull. I would usually have a bit be able to last through 5+ hours of constant cutting. Used the same settings as I had done before and I broke a bit in less than a minute. I started tweaking the settings to see if I could actually use the new bits and I broke 5 bits in the process. Ended up having to do lighter passes (from 0.125" to 0.09") and slightly higher RPM got a bit to last almost an hour but it still ended up breaking. I used to do 3 passes at 0.125", had to go to 4 passes at 0.09" for these new bits and am currently trying 5 passes and seeing how far I can get with that. Current settings are 0.075" cut depth, 25 IPM, 18000 RPM.If you look closely at the attached picture, the bit on left has a visible "edge" and looks more parallel. The bit on the left is an old/used bit. The one on the right is new bit with the cutting edge at the bottom of the "cone" and the bit has visible tapers when look at it from the side.It would have been nice to know that the cutter geometry changed before I ordered 60 bits. Previous bits were a great deal for me. Now it seems like I need about 5 bits to finish 1 job - just not worth the time. Seems like a bait and switch. The old bits were much better value.

I started using the Dremel 561 multipurpose cutting tool to cut away treated deck board to expose square head stainless deck screws for removal. The 561 bit didn’t last very long. About 60 holes before it was too dull to cut.I purchased these mostly for the quantity (10) thinking I might be able to get through the entire deck with 10. So far, I’m still on the first bit and it has already done 4x what the 561 did and there’s still a cutting edge. Very happy.Note: the Dremel 561 came as a kit with a depth gauge and cutting shield. These bits are “shorter” than the Dremel brand and my not work effectively if used with the Dremel depth gauge attached. I’m not using it so they work for my application.

Bought to work in Aluminum on my CNCEST 3040T Router with 400W Spindle. They have worked very well so far at 250mm/s with a 0.3mm depth of cut(DOC), with full and partial engagement of the mill. An error in my G-code generator sent one of these mills directly into a 2.75mm high wall of Al at 250mm/s, and it did a heroic job for several millimeters until the mill used up all of the slack to wander off center of the direction of cut and broke. But, I have 9 more. I must say, that this set seems to be a very good value, and I will evaluate larger DOC and/or speed values with these end mills.Would definitely buy more. if still available, when needed.

I'll start by saying they lost a star because one of the pieces was broken out of the box. I can't give 5 stars to poor quality control. They were fulfilled by Amazon but I can't imagine one broke sitting on the shelf in some Amazon warehouse. I could definitely have returned them and gotten a replacement but I needed to use them and didn't want to hassle with that if the remaining 9 worked, and they did.On to using them. I'm cutting a text outline and needed a 1/8" bit that could do cutouts on 3/4" walnut without burning or breaking and these 2 flute upcut bits worked great. They ejected the majority of the chips even on the deeper cuts leaving the cutting path clear for the next pass. Swarf in the cutting path is a big contributor to burning and bits breaking so chip ejection is key, and these did a great job. They were also sharp enough that I had no tool marks or tear out on the edges that needed cleanup. When these get dull I'll buy another set, hopefully of 10 and not 9 and be happy with them.

The bits come sharp and work well on the hobby CNC. But when used for cutting using the sides (and not just the tip), they get dull quickly when cutting MDF.

Fast delivery, seems to me bits stay sharp almost as long as much more expensive brands.

Es una herramienta muy fuerte y permite hacer cortes muy precisos

fast shipping, work as intended

Très bon end mill pour le bois