Black junction box

I use such boxes for watertight connections on boats. This manufacturer happens to have many, many different sizes and configurations, and the one I chose fell right between two sizes offered by another manufacturer. In other words, the size (an oddball size) of this box was “just right”. In addition, this box is extremely well-made. It comes with a silicone rubber gasket to install on the lid to ensure waterproof integrity. Much to my amazement, it also came with FOUR cable glands, two each of a size, so any cable entering the box can be sealed off to prevent water ingress. The screws are genuine stainless steel, an important feature for wet locations. The 4 pre-drilled holes for mounting the box are each tucked in a corner, and “live” outside the waterproof section of the box so no caulking of the mounting holes is necessary. The 4 mounting holes are completely independent of the watertight compartment. Very clever indeed! There are 4 shouldered areas inside the box which will accept small (probably #6) sheet metal screws for mounting a terminal strip or other electrical items (relays, etc). It’s rated IP65 for water resistance, and I absolutely believe it. This rating means it is dustproof & can resist low-pressure jets of water (like rain or splashing water). I’ll definitely be buying more of these boxes in the future

I made good use of this black ABS project box. It appears to have a good weather protection from its included seal too, which is just what I needed. I also appreciated getting some fittings included within the box for my low voltage multi-wire cord connections. I was able to drill several very clean holes for cabling, switches & LEDs and do some odd shaped cuts with my Dremel tool. It cut very nicely. No chipping or other issues that one might experience with a lessor (non ABS) box. This is the plastic material that is good for this sort of thing. I am quite satisfied as it worked beautifully for my project! I added this box to my Champion inverter so that it would be fully remote control via a series of RF relays all triggered by a simple 4-button key FOB. There are 4 different colored LEDs on the panel of the box with a push-button on/off switch in the center. Thanks to this box I can now control Start, Stop, Choke & Eco Mode and know exactly what is going on with it without having to go outdoors when using the inverter as a whole-house power backup for common winter power outages. I trust the quality of this box to safely maintain the integrity of my electronics and recommended it. Here are a couple of pics of the box on my new 'Wireless Inverter" project. (with FAT tires too. Oh yeah!)

Good quality and are true to size. Not thin and cheap. Im super happy!

I purchased the larger of the two listed, (200 mm x 120 mm x 75 mm), to use as a button box for my PC. The box was as described when arrived. The weatherstrip for created a waterproof seal for the lid is included, but not installed. Took a moment, to manually squish it into place, and the length of rubber cord given was just perfect to meet end to end. Using my surface mount drill press, I carefully and easily drilled holes into the lid and body for mounting the switches, buttons, and cord access I needed. After the first two drills, I felt confident enough, that this wasn't going to crack or shatter drilling the rest. (However, I would still recommend taking it slow and easy when drilling through plastics. If anything, you want to make sure you're chewing through them with the bit, and not just melting it via friction.) Plenty of space to work in the box, and I had ample room left over after installing one power light, 10 push buttons ,and two 3-way switches on the lid. The "prototype" came out great, and I'm looking forward to using these boxes in the future for other projects. This is a good, low priced box, perfect for experimenting with and not worrying about breaking the bank if you make any mistakes or don't like the finished project. A perfect "prototype" box if you will. Like what you did, redo it with something higher grade, such as an aluminum box for for final build. 4/5 Stars.

Awesome project box that was perfectly sized for the circuit and install that was planned. It was very easy to cut Acrylic panels to hold electronics because the listing had accurate dimensions! The thickness of the Plastic was great and the weathertight gasket provides a positive seal that has kept the build nice and dry and the electronics well protected! Included were high quality stainless steel screws that provide a a great look and will not corrode over time. I ended up fixturing it down to my cnc to carve holes to accommodate led holders. I scratched it during manufacturing and it buffed up nicely back to a high polish! This case has held up to the elements in the summer heat, rain and imagine it will do well in the midwest winter. I will be using these boxes in the future for many other projects!

I ordered to make my own control box for trolling motor and it worked out great. Solid product

Yeah, I like and use these boxes for various electrical & electronic projects. They can be drilled, carved & etc for any purpose necessary to integrate into a project because they're rigid but with some pliability, and tough too! I usually have a few around of different sizes. If an idea pops up, I check my supply. Possibly the best feature is economical pricing. This box also comes with two cord glands, and two plug bosses, with caps. Really great additions--especially for the low price. I'll certainly buy more in the future, (well, I'm 81, so . . .)

This box is an exellent choice for anyone who is making an electronic project that will be subjected to a harsh environment. It appears to be made of a tough plastic and it has a perimeter seal where the lid connects with the body of the box. It has brass inserts at the corners that are threaded for the included machine screws to give a metal-tp-metal connection. Altogether, this is a good product.

Took almost 2 weeks to arrive, but when it did the quality is amazing. Very strong and sturdy, seals nicely and did the job above my expectations.

このお値段で２つ付いているのはお得ではないでしょうか。 １つずつフィルム包装されているのでいいと思います。

Es básico pero de buen material, un poco delgado pero v su es resistente

近接センサーを小型基板に載せたものがあり、その埃除けのためのボックスとして利用した。 質感、精度、材質ともに満足。 2個セットだったので余計な買い物になったかと思ったが、1個目で穴開けに失敗したので、予備があって助かった。 今回、たまたま基板やプラグの寸法にぴったりのサイズの商品だったが、もう少しサイズのバリエーションがあるとなおよいと思う。

Well made and sturdy construction