T&S Brass B-0230-K Installation Kit for B-0230 Style Faucets. Two short elbows, nipples, lock nuts and washers that provide 1/2" NPT male inlet and outlet when assembled

After reading a few negative reviews I wondered what the problem was with this product, some were whining about. There is no problem with the product at all...none! Just inexperienced people trying to play home plumber with no real trade experience. This kit is the cats ass. I hooked up my triple compartment commercial stainless sink with no issues, no leaks. Now for those that want to use this product, I'll give you some professional advice, I'm a steamfitter with over 40 years at it. Use Rectorseal, Gasoila or another soft set thread sealant on ALL of the threads, not teflon tape.. You'll have no problems. Remember to tighten all of the fittings with wrenches. Double nut the nipple when you install it in the 90 and tighten it until it stops, then install the 90 with nipple into the back of the sink into your fixture. It ain't rocket science folks. If you can't do it properly, hire a professional.

Bought a different brand or supply nipples and elbow at first but the threaded nipple wasn't tapered and the elbow was just a large brass pipe fitting like you get at the home center. The nipple was also 3 inches long so the sink sat an inch away from the wall with everything assembled which looked sloppy. Also, one side kept leaking so I came on here and this looked like a more compact mistake proof solution. Installed it last night and the sink is tight to the wall and no drips. I'm a happy camper.

This is a must have product for installing a wall mount faucet on a utility sink. I just installed the Kingston Brass KS213SN wall mount kitchen faucet with cross handles on my stainless steel utility sink. The TS Brass installation kit is the only kit I found online that even looked like it would work. And it worked perfectly. I couldn't find any similar installation kit locally. This kit provides a secure, tight, strong installation for the faucet. It was a very easy and quick installation.

These are good. But don't try to use it for anything other than stainless sinks. The nipples are too short, I tried on a Kohler porcelain sink with a back apron and the nipples are too short for the 1/4" sink thickness. If you need to install in a thicker sink buy the "TS Supply Nipple B-0425" They come in various lengths, then get elbow separately. For reference the nipple in this kit is 1 5/8" - for a porcelain sink 2" did the trick. Quality is good other than that. FYI the correct sequence to install these is: Use both nuts on a single nipple as jamb nuts to tighten into faucet fitting. That's how you get the leverage that most people seem to be complaining about. Once the nipples are in faucet, Install washers and nuts and tighten to sink, lastly install elbows onto nipples. That is how these are supposed to be installed.

Fit what I needed them for

Ordered three of these (for 3 T&S faucets--to make installing easier) for our antique 6' Kohler cast iron wall mount high back sink, and 2 out of 3 were good. The third one had bad threads on the nipple--not noticeable at first glance, but wouldn't work when I tried to connect the two pieces. Great items when they work. Still says they are made in China, of course... Returned the bad one and ordered another one--we will see if the threads are good on the nipple.

These are the ones to get!! Boy, wish I knew about these before. These are a must if you are installing a faucet on a backsplash, etc. I purchased some comparable mounting kits (unfortunately 4 of them at $25/ea) that were utter pieces of crap. Poor fit and incorrect nipples with no taper. Impossible to get to seal. Copious amounts of teflon and paste.. nope, no dice, after an entire day of removing and installing the same faucet. These on the other hand were phenomenal. Easy to seal, didn't even have to tighten very much, due to the correctly tapered brass nipples.

Used this to mount a moen 8126 to a gridman utility sink just like another user. This hardware accomplished the install perfectly. Just turned water on and zero leaks. Watched a few YouTube videos before the install, but that's the extent of my experience and this is my first real plumbing diy job. Used teflon tape. I would advise users to make sure they apply the tape in the correct direction. Also worth noting, my sink was able to be mounted flush to the wall using these.

These adapters make commercial faucet installations so much easier!

All great...thank you ;)

defiantly need this to attach to sink. should be included with product or strongly recommended when purchasing taps

Don't use Teflon tape, use the paste/puddy or you will never get a seal.

quil delivery exactly what I needed