Car LED Strip Lights, 2 Pcs 24 Inch Flexible Headlight Strips DRL Light Tube, Dual Color White and Amber Daytime Running Lights Waterproof Neon Turn Signal Bulb Sequential Switchback

These are easy to install and they look great. I watch the install videos and it made it pretty simple. The pins at the end of each wire is meant to be pocket into the corresponding headlamp turn signal wire. This make it easy to install. My care (04 honda element) didn't have a daytime running light so I made my own by using some of my own wire and tapping into the ACC fuse (the fuse that turns on all the dash accessories).The double sided tape that comes with the product isn't good and I highly recommend, if using this on your car, to use stronger stuff. I also found a suggestion to use reflective tape on the outside of the light assembly (if that's where you're mounting it), to prevent unwanted light leak to the inside of the assembly. Overall super happy with it.

I don't normally write reviews unless I am very impressed with something are very unsatisfied. I am very impressed with these lights. I install them on my Ford F-150 pickup just for the DRL lights. They are very bright and seem to be good quality. Yes you have to use something other than the glue if you bend them around. I use some gorilla duct tape behind it and it held very good. I am just using the DRL bright lights and not the turn signals, but they were easy to install and seem to be great quality. We will wait to see how they last.

I've only had these things installed a week, but they are working quite well in many lighting conditions. Quite honestly, I almost think they may be a little too bright! But nice to know i'll be seen from miles away!Install and wiring notes:I decided to use and installed a 'fuse tap - 10 amps max' (see pic 2) on to my existing ACC fuse. I then connected the fuse tap red wire to to 18 gauge red primary wire that was run through the firewall into the engine area, ran along one side of the engine area, long enough to reach both headlights. I used velcro to keep the wires neat and out of the way. Both LED light wires (red) were spliced/soldered to this red primary wire. Note that each light is around 1amp, so a very fractional amount of amperage needed. The LED light wires (black) were spliced/soldered to 18 gauge black-colored primary wire and ran to the negative battery cable frame bolt and connected to the bolt with circular terminals. The LED light wires (yellow) were spliced/soldered to the turn signal light positive cable, to allow for the synchronized turn flashes.I positioned the lights flat, along the inner lip of each headlight. This allowed for the side of the light to stay exposed, and visible in-between the headlight and grille/hood. This method was a choice for me, as I originally tried having the lights facing forward in the front of the headlight, but didn't like the way the exposed LED looked while the truck was not running. I felt it looked better with the thin side facing forward. It's still very bright!Total time: around 2 hoursPros:Extremely bright, day or night!Very nice look!Cheap!The amber turn signal lights are a bonus feature!Cons:Will require significant wiring to get it to work.

Had to use some 3m trim adhesive on the ends, but do love the way they look on my 2005 Yukon. UPDATE: 7-25-19: I still love the look of these and the White with Amber turn signals works awesome. CON: the adhesive on both Strip tubes failed. Removed the old adhesive strips and used Permatex heavy duty trim adhesive to hold them on my headlight frames. UPDATE 1-21-21: still working like new. had to re-glue them on my headlights last year in June 2020. The 3M adhesive is definitely crap, but the quality of the lights are excellent!!! thinking of getting another set just in case the old ones die!!! go with black permatex heavy duty not the yellow!!!!

The media could not be loaded. I bought this to add turn signals to my side by side. They have Daytime running lights as well, it looks good and adds a lot to my machine, but... 1st problem I noticed was one of the strips was not marked where it could be cut, I knew I was going to cut both of these to fit around the light housing. I tried to find where I could talk to the seller, but it was all Amazon, I didnt have the time to send it back so I took a gamble, measured the other one where I cut it and tried my best to be precise (not the easiest when you are cutting an outer shell, then the led tape inside) the gamble paid off this time, I hope its not just enough off that its a ticking time bomb and will stop working when it gets jiggled. The second issue was with the adhesive. No matter how hard I tried to pull the outer strip off to reveal the adhesive, it would pull itself off of the strip, I pulled the first one off, and some adhesive stayed, than half way down it pulled all of it off of the strip. Luckily I have some 3M tape that fit, on the second one, i just pulled the blue tape off, and pretty much all the adhesive came with it. I was actually worried about the adhesive, 3M is by far the best at this stuff, probably money ahed with it anyway, but still, it is a pain. I know led's dont take much energy, but the wires on these are so small, my stripper doesnt even work, i got them stripped, but looks like about 5 strands in there. Hopefully I have installed is suficiently where it wont move much and break to wires, would have easily paid a little more for some heavier wire.

I bought these in May of 2020 and haven't had any issues with them. All the LEDs are still working and they still function like the did when I first put them in. This was an easy install and I have had several people say something positive about them just out of the blue. I highly recommend them.

The media could not be loaded. Love the look of these lights! The led strips are nice and vibrant and easy to install. Had these on my vehicle since 2020 (3 years ago) and they are still working.Only con would be that the adhesive is not so good...so I had to use 3M double sided tape to have them stick better to my headlights. Seller had good customer service and communication. Would definitely recommend!Pros:-Bright lights-Easy install-3 years+ and still running good-Reasonable priceCons:-Adhesive on the strips aren't good-The buldging end caps on each end of the strip (if they could use a thinner rubber or make it all in one piece, the led strips would look more sleek and not have thick rubber end caps exposed. (Ideas for future designs?) Also on that note, somehow have the amber lights flash as you lock or unlock your car would be nice.

Very nice quality item and well packaged. Not fitted mine yet waiting for the engineer, but the length is just right to cover a large headlight unit in an L shape. One thing I will do however is add another strip of 3M two sided sticky tape. I buy it from Amazon too. The strip lights can take a fierce head on weather like snow and ice, so I'm going to double up on adhesion just to be on the safe side.

Facile installazione

Eclaire très bien mais demande un minimum de connaissance en électricité car j'ai dû créé un faisseau pour les feux de jour et pour le clignotant il faut le brancher sur la cosses du phare à l'emplacement du fil du clignotant pour le raccordé

werkt perfect met IC decoder.mijn vorige waren zonder en die werkten niet zo als verwacht. Gemakkelijk te monteren en af te knippen volgens lengte.