OriGlam Adjustable Two Jaw Bearing Gear Puller Remover Tool, 2 Inch Carbon Steel Pump Removing Kit for Motorcycle (2 Inch)

I was pleasantly surprised at the build quality and sturdiness of this puller. I needed to replace a gear on a car sunroof window motor, which was pressed on tightly. It worked without a problem. This is perfect for small gears and pulleys. It is both stable and durable for any small, tough job.

Bought to pull a 1-in bearing. It's not the best made product but it does the job and that is what is the most important. There is not a lot of moving parts to this and it's very easy to use. The one thing I do not like is the handle falls out but you can just use a crescent wrench or a socket.

Comments regarding imprecise tooling appear valid. This product tends not to center the push screw correctly when set up for pulling. While it is a little crude, the irony is that this product does a job that many of the others of its general category cannot do because of critical dimensions and adjustment features. In my case (right out of the box) with a little nudging, this tool accomplished the job of pulling a pinion off of a 5/16" shaft in rather short order. I don't mind crude tools when they get a job done.

I got this to pull the wheels from O scale locomotives when repairs were needed. I did not like any of the other units out there, some even made out of plastic. This is a well made tool and fits and works perfectly. For my use though, I needed more of a cylinder shape on the end of the puller screw. not a point, but still, it did fit the wheels, and did push out the axle. On most I could pull the wheel off after the puller reached its limit, but on a few, I had to add a Phillips machine screw taped in place to extend the reach.

Needed this for a washer machine repair to pull a gear off of the washer motor shaft. It worked perfectly and saved me the cost of having to buy another washer motor. Very solid, small puller.

I've bought a lots of tools that I will probably use one or two times in my life. To save a little money I will sometimes buy items made in China. This gear and bearing puller was the WORST piece of crap I've ever received. I was working on a deadline and didn't have time to wait for a replacement thought I doubt it would have been any different the second time around. One of the "jaws" was a full millimeter longer than the other. The crossbar had only been finished on one side, so the jaws wouldn't slide all the way to the center like they are suppose to. I actually had to take the crossbar to my grinder and remove cast iron until I could get the jaws to center and reduce the top surface enough that the jaws were aligned. Granted, it only took about 10 minutes to get it ground down and trued up enough that is was "usable". The center screw came with a point on it. After pulling the first 16mm x 10mm pully from a 5mm shaft, the "point" was now about 2mm across. After the second pully it was at least 3mm wide! I don't know what grade of steel they used, but it was VERY soft. Really total junk after two small pullies!!

Worked just fine for my needs.

The reason I bought this gear puller was because the other common small gear puller sold here is aluminum and several reviews show it breaking apart upon use. I knew when I bought this I'd have to do some work to it, I just didn't know exactly what. Please refer to the pics. The good thing is that this is made from steel and should hold up under pressure. The bad thing is that it's basically hand made and suffers from very very rough forging. What I wanted this to pull is small pulleys on my 3D printer. Due to the inexact forging it does not close up to a small diameter evenly. The metal is "blobbed" out too far on one side of the center screw. This prevents one side of the jaws from getting to the same distance as the other side close-in. I can only imagine the poor soul making this thing in some sweat-shop. To fix it I got out my grinder and vise and went to work. I worked on it for about 20 minutes until I got the "blobbed" out side cut back so it would allow the jaw to close in like the opposite side. I also cleaned the threads (M10 x 1.5) of burrs with a tap and die. This fixed it to my satisfaction. All I need to do now is re-paint it. Giving a rating of 3 due to poor quality control.

Ich musste bei meinem Motor das Primärzahnrad wechseln, es saß seit 65 Jahren bombenfest auf seinem Konus. Es gibt ein teures Spezialwerkzeug dafür, aber ich habe es mit diesem Abzieher versucht. Zunächst habe die die Spindel des Abziehers gut mit Motoröl geschmiert (Fett oder Öl ist dabei egal, hauptsache nicht trocken verwenden). Dann den Abzieher angesetzt und mit einem Ringschlüssel mit viel Kraft an der Spindel gedreht. Damit hat es gut funktioniert.

Very cheap, used it on a rega 3 record player to change the motor rotor and it worked perfectly. The official tool was about £40 this was far far less

Very happy with it thanks

Bon produit parfait

OriGlam Adjustable Two Jaw Bearing Gear Puller Remover Tool - high-quality tool and highly recommended.