We remain fully operational. Our teams are working around the clock to ensure your deliveries continue safely.
下载应用程序
🔴 Stop Smart, Reset Smarter: Your CNC’s Safety Sidekick
The Genmitsu CNC Router Emergency Stop Switch is a compact, push-button safety device designed specifically for 3018-MX3 and 3018-PROVer models. Rated at 250V AC and 5A, it provides instant machine shutdown with a lock feature and software reset capability. Featuring a 20cm cable and standard 2.54-2P connector, it ensures easy installation and reliable emergency control for your desktop CNC setup.
| ASIN | B0834SV7F9 |
| Actuator Type | Push Button |
| Best Sellers Rank | #176,824 in Industrial & Scientific ( See Top 100 in Industrial & Scientific ) #740 in Pushbutton Switches |
| Brand | Genmitsu |
| Circuit Type | 1-way |
| Connectivity Protocol | Wi-Fi |
| Connector Type | Crimp |
| Contact Material | Copper |
| Contact Type | Normally Closed |
| Control Method | Touch |
| Control Type | Emergency Stop and Software Reset |
| Controller Type | Push Button |
| Current Rating | 5 Amps |
| Date First Available | December 25, 2019 |
| International Protection Rating | IP54 |
| Item Weight | 0.01 ounces |
| Item dimensions L x W x H | 3.46 x 2.83 x 1.54 inches |
| Item model number | 101-60-388 |
| Manufacturer | Genmitsu |
| Mounting Type | Snap In Mount |
| Number of Items | 1 |
| Number of Positions | 1 |
| Operating Voltage | 250 Volts |
| Operation Mode | Push Button |
| Product Dimensions | 3.46 x 2.83 x 1.54 inches |
| Terminal | Button |
| UPC | 816550023167 |
| Unit Count | 1 Count |
| Wattage | 1250 watts |
R**N
Smaller than photo shows but works as intended
Perfect, yet tiny, "kill" switch for the multitude of 3018 style desktop CNC engraver machines. Yes, it is pretty light duty but remember it's designed as emergency kill switch, hopefully rarely needed and not a main power button. I 3D printed a mounting plate and mounted the switch, ran wires to the controller board and it tested fine. Now I have one more safety to kill the machine when I do something stupid! 😏
J**U
Worked OK with adjustment, but I didn't read the listing well so its my fault.
I ordered this for my 3018 pro. Turns out this is specifically for the models mentioned, and was a little inconvenient but otherwise fine for mine. Clearly I have a problem reading. This is a NC switch, and the board I have expects NO, so the operation was backwards. Easy to fix by rewiring the back of the switch with a soldering iron. Very short wires about 6-8 inches; plan to extend the wires or to install it very close to your control board.
A**R
Works as expected, may require minor rewire if you don't have the actual "PROVer".
Works as expected, may require minor rewire if you don't have the actual "PROVer". Like many other reviewers I had to swap the red wire from the outer "NC" terminal to the middle "NO" terminal. A few minutes of soldering. Not a big deal.
R**P
Handy little switch with no directions
Nice little Emerg Stop Switch. It fits a 5/8” hole (0.620). Be careful where you mount it as threaded shaft is about 3/8” long. If you mount it to the upright of a cnc, you will find you cannot use the included nut so I siliconed my switch in the hole. There are no directions with this switch and I believe it is intended to be mounted to a sheet metal plate. Your cnc controller may or may not have pins soldered in the circuit board so you may need to solder in pins.
P**L
great add on
a great add on to cnc machine would say a must to shut your machine down quickly. easy to install mount and connect to control board
A**N
Didn't Work
The switch was wired incorrectly, worked after I re-wired the correct contact on the switch Needed NO terminal wired not NC. When it arrived it worked as an Emergency ON switch not an Emergency OFF switch it was supposed to be.
J**S
Great
Works great as a double e stop
A**M
Peice of garbage. 2nd button & will not reset.
Don't waste your money. The one I got with the machine got presses while I was installing on my 3018. I was having issues with my 3018 until I figured out the e-stop couldn't be reset. I decided to buy a replacement e-stop. I thought, "I'll test it out." Pressed the button & it won't let me reset it. It is stuck in stop position & then the button fell off. Tried to reset position. Nothing. Don't buy this it is a 1 time use.
E**O
Item is small which suits the 3018 PRO Perfectly
A**I
ちゃんと最後の隅々まで読まなかったからいけないのですが、写真じゃ２個と❗️中身は１つだけでした。ちょっと紛らわしいな。
R**T
Need product for home made CNC mill
B**H
Bought this to replace the on/off switch on our tread mill and works great so far not the recommended way of having an emergency shut off on a treadmill but works for us
S**M
It was set up for different machine than mine but a good quality device
TrustPilot
4天前
2 个月前