Sovol SV01pro 2023 Flexible Steel Platform, One Side Textured PEI Surface, Another Side Build Surface Sticker Sheet, Coming with Magnetic Bottom Sheet for Sovol SV01 SV01 pro SV02 3D Printer

It’s so good to the point sometimes my prints stick TOO well. That’s not a bad thing but it can be frustrating when doing leveling tests (~1 layer thick)The coating is super hard and won’t come off if you use the scraper, but I’m still gentle if I ever have to pry something off. The steel bends a little bit to help take prints off once cooled.I attached a picture, left is the original Ender 3 magnetic sheet, right is this product. Note the difference in texture. I also had a PEI sheet before this (changed out because I messed it up while troubleshooting my extruder, and left the 200C nozzle too close) - that sheet’s prints felt and looked smooth, while retaining details. This one is coarser than the stock Ender, while retaining details.The only thing I haven’t figured out is why my black PLA looks a little grey on the bottom.So far between the stock Ender sheet, PEI, and this, I like this the most. I feel like I could print something 12” tall and not worry about adhesion. PEI was a little iffy at times and I definitely had to use isopropyl alcohol to clean it occasionally - I haven’t tried glass but I hear the clips and hair spray/glue can get annoying.

I got this flex plate for use with an Artillery Genius 3D printer which has a bed size of 230mm by 230mm. I suggest to measure/check your bed size before purchasing to see if it will cover what you have.I primarily print PLA, PETG, and a little TPU. This plate is compatible with all three, so I gave it a shot.PROS1. Creates a nice texture on the bottom of prints.2. Holds prints nicely.3. Pretty easy to get completed prints to release sonce it is a flex plate. No release agents were necessary. One note is that if printing with PETG or TPU it would be a good idea to remove the print while the sheet is still warm. I found this makes it easier to remove smalls pieces of supports or skirts that tend to get left behind on the plate.4. This is cheaper than a lot of the similar products that are available.CONSThere really is no documentation from Sovol that I found that is available on applying the magnetic sheet to the existing bed or any other product usage recommendations. The good news is that there are similar products that you can search for installation videos if need be. I am familiar with using similar products, finding my own answers, and experimenting, so, all in all this is not a big deal.Other notes:The black surface is some kind of polycarbonate and has a sort of gritty, sandy texture. According to a rep, the whole setup is limited to 110c in temperature on the heated bed. I don't print anything that requires anything close to these temps so no problem. The black surface comes pre applied to the flex sheet. The magnetic sheet has adhesive that gets applied to whatever bed you are currently using.

I have several 3d printers and have found the gold colored steel plate PEI bed sheets seem to offer the good mix of adhesion vs ease of removal vs flatness. This one is a good fit on a SV07 Plus as the bed size was the same.

Bought this to upgrade to a spring steel bed for easier removal of prints, and because the original build surface on my Anycubic Mega Zero 2.0 didn't withstand the bed heat needed for ABS printing. This was a perfect replacement, it actually fit better than the original magnetic build plate which was just a bit oversized.WARNING - DO NOT PRINT PETG without some kind of release agent.While removing the print the PETG was adhered so well that it actually ripped a chunk of the build surface sticker off. Now I'm not sure if the sticker should have held up, but I'm chalking it up to user error. I am currently in the process of looking for and ordering a new build surface sticker, but otherwise this seems to be inexpensive solution for low end printer flexible build plates.

When I got this plate in I immediately cleaned it with alcohol to remove any manufacturing gunk. There was a small glob of black what I think was grease so I sprayed the plate again then noticed that all of the white paint was coming off with the alcohol. I've cleaned the stock plate more than I can count and have NEVER had this happen. Also, this plate seems to be .2mm thicker than the stock plate and required me to completely recalibrate my printer. Very poor quality control.

The texture compliments the layer lines well.

This is the second magnetic flexible build plate I have purchased for my Sovol SV01 printer. Got the first when my glass build plate started to wear out. Both of my magnetic build plates have failed in a similar fashion. The first got a bubble between the grip surface and the underlying flexible metal plate. The pictures here are from the second one that did not even survive its first print. Again a bubble formed under the print and when removed the grip surface ripped away. Even my worn out glass plate did better than this, very disappointing.I will be returning to the textured glass build plates from now on. Unfortunately I now have a magnetic surface permanently attached to my aluminum bed, but not too much I can do about that now. The glass plate still works on top of the magnetic surface.I don't recommend these magnetic build surfaces because they do not last.

Don't know why, but this needs to be cleaned every other time you use it - I use Dawn and a little scrubber, then it works fine, otherwise nothing will stick (TPU and PLA). Also you'll need to bump up the temps as this thing acts as a thermal barrier. Still a good product...

Perfect replacement and print stick perfectly

よく付きます。

これに変えたらPETGで失敗しない

【更新】 セラーにコンタクトしたところ、適切なサポートを受けることができたため、★4個に修正【初回レビュー】 古いEnder-5 Proのアップグレード用として購入。純正ガラスベッドと比較すると、ファーストレイヤー定着率がむちゃくちゃ向上しており、早く買えば良かった状態。しかし残念なことに白線グリッド模様がワーク側に転写されるという謎の現象が発生しており、初期不良の疑いで発売元に問い合わせ中である。当然、転写された部分の白線グリッドはだんだんハゲてきて意味不明な状態となっている。（PET-Gフィラメント／ホットエンド240℃／ベッド温度70℃）既にマグネットプレートを装着している人は多いと思われるので、PEIシートのみの商品構成があると良い。

シボがあるテクスチャードプレートでかなりガッチリ定着します。剥がす時も問題無く綺麗に取れます。が、、プレートに印刷してあるグリッドラインの塗装も一緒に剥がれて造形物に付着するのはちょっといかがなものかと。たぶん白や明るい色のフィラメントだと目立たないのしょうけども。そして塗装が剥がれなかった所も薄いラインとして残りますのでせっかくのシボ模様も台無しです。何といいますか、グリッド線などコストをかけて印刷して造形物のクオリティを落す意味が全く分からず少々困惑。ビルドプレートの上のプリント要りますかね？食いつきや剥離が問題無い分、勿体ないなあと思う次第です。