Q: Can photo cell turn lights on at dusk and then the timer turn the lights off after a set period of time?

Both photocell and timer are needed. If you install the photocell and timer (Mechanical Timer: B079B2TNMR) (Digital Timer: B01N9T3TLW) on our multi-tap Low Voltage Transformer, the photocell can turn on the power at dusk and the timer can be used to turn it on/off at the appointed time set by the timer. When it is bright, the power will automatically be turned off by the photocell regardless of the timer setting. Following is an example of the situation. Use a timer and set the turn-on time for late evening, while it is still light. Perhaps 4:00 PM. Set timer off time after dark at 10:00 PM. This way will turn on lights at dusk when triggered by photocell. The timer should already be on. Photocell will continue in 'on' mode, until the timer goes into 'off' mode (at 10:00 PM), turning lights off.

Q: Can this unit be mounted onto wood siding?

If the wood is sturdy enough, should be no problem. I mounted the unit on a stucco exterior and it worked fine. Would be a good idea to find a stud if possible.

Q: What is the maximum output amperage?

The correct answer is 2.5 amps. The formula to convert watts to amps is: I=P/E so 300W/120V= 2.5A. This is assuming you have maxed out the transformer at 100%, drawing the full 300W. You could connect two of these transformers to one standard 15A electrical outlet. Hypothetically, you would draw 5A from the circuit if you have two 300W transformers at 100% capacity.

Question 1

Max load 70%? Is this a 300w or 210w transformer

Accepted Answer

The “Maximum load 70%” means the total lighting fixture load should not exceed 70% of transformer wattage (total lighting fixture wattage <= 70% transformer wattage). It is because there is voltage loss along the wire. The voltage loss depends on lighting fixture load, wire gauge, and wire distance between transformer and lighting fixtures. If the wire distance is shorter than 200 feet, the maximum load on the lighting fixture can be higher than 70% (for example, 80%, 90%...).

Please feel free to contact us at cs@lightkiwi.com if there is any additional question or inquiry. Thank you!

Regards,

Customer Service
Lightkiwi

Question 2

Can photo cell turn lights on at dusk and then the timer turn the lights off after a set period of time?

Accepted Answer

Both photocell and timer are needed. If you install the photocell and timer (Mechanical Timer: B079B2TNMR) (Digital Timer: B01N9T3TLW) on our multi-tap Low Voltage Transformer, the photocell can turn on the power at dusk and the timer can be used to turn it on/off at the appointed time set by the timer. When it is bright, the power will automatically be turned off by the photocell regardless of the timer setting.
 
Following is an example of the situation.
 
Use a timer and set the turn-on time for late evening, while it is still light. Perhaps 4:00 PM.
Set timer off time after dark at 10:00 PM.
This way will turn on lights at dusk when triggered by photocell. The timer should already be on.
Photocell will continue in 'on' mode, until the timer goes into 'off' mode (at 10:00 PM), turning lights off.

Question 3

Can this unit be mounted onto wood siding?

Accepted Answer

If the wood is sturdy enough, should be no problem. I mounted the unit on a stucco exterior and it worked fine. Would be a good idea to find a stud if possible.

Question 4

What is the maximum output amperage?

Accepted Answer

The correct answer is 2.5 amps. The formula to convert watts to amps is: I=P/E so 300W/120V= 2.5A. This is assuming you have maxed out the transformer at 100%, drawing the full 300W. You could connect two of these transformers to one standard 15A electrical outlet. Hypothetically, you would draw 5A from the circuit if you have two 300W transformers at 100% capacity.

关于我们

客户服务

客户支持

区域访问

法律与政策

社会的

获取应用程序

Lightkiwi W9715 300 Watt (12V-13V-14V-15V) Multi-Tap Low Voltage Transformer for Landscape Lighting

细节

描述

有问题吗？看看别人问了什么

常见问题