Rev-A-Shelf Cabinet Door Mount Kit for Kitchen Base Cabinet Organizers, Pullout Storage Shelves and Drawers, Trash Cans, 5WB-DMKIT

I just finished installing these in seven of our kitchen cabinets as icing on the kitchen remodel cake. Really tired of getting down on the floor to pull out the heavy mixer or juicer from the back in the bottom of a dark cabinet. UPDATE: 1 year and all units are working great. No issues. Pros: Nice chrome finish and fairly sturdy. I would have preferred the Rev-A Shelf birch wood units but too expensive for our budget. These are reasonable in comparison. Assembly of the unit is about 10 minutes. Cons: Installation took a couple hours for the first one. Maybe 20-30 minutes for each additional unit. Some things were not obvious. See tips below. Several assembly screws easily snapped off. Glad there were extras. My experience: The units are 1/2" smaller than the cabinet opening. I ordered for an 18"w cabinet opening and the unit is 17.5"w. That allows for clearance for protruding door hinges. The instructions said to mount the unit away from the door hinges (off center in the cabinet) which leaves a 1/2" gap on the hinge side. That side just stands in the air unattached or anchored. Being off center bothered me. I would need to add some kind of blocking to move the units to a centered position. In my case I also ordered the door mounts to convert the doors from hinged to a pull out configuration. That's where my confusion started. The door mount brackets were off center from the doors position directly below the drawer because the units were installed off center. I didn't have enough door frame to mount the door that off center. There are round discs (spacers) included with the door mount bracket kits that will allow you to move the brackets left or right but it looked odd to me. I realized that I could use the round discs (spacers) to center the whole unit by using the spacers in between the unit frame and the door frame on either side. The four spacers provided at the four front anchor points. I had to provide longer screws to make this work. The result was a centered unit in the cabinet opening with a centered door pull. See pictures of the spacer positions. Tips: 1. Hand tighten the assembly screws. They snapped easily with a screw gun, even with the drag set low. 2: If you are installing the door brackets (separate kit) use the spacers to center your unit in the cabinet opening rather than off center. See pictures 3: Install the drawers so that you are sure the brackets that attach to the back of the cabinet are truly parallel and won't bind the drawer slides. Mark the holes, remove the drawers and mount the rear brackets. Then attach the unit to the bottom/base with the four screws provided. 4: Mounting the door to the brackets: Attach the brackets to the bottom drawer. Tighten the screws just until the brackets stay in place but can still move if pushed with some force. Apply the the double stick tape to the bracket faces. Pull the drawer slightly so that it just sticks out beyond the cabinet face. Line up the door panel under the drawer face right to left and also the door top down from the bottom of the drawer face. Press firmly in toward the brackets so that the brackets adjust from the pressure and the double stick tape adheres to the door panel.. Carefully open the door/drawer and attach the screws. Note: The instructions said to face the brackets outward. This did not work for our doors so we turned them inward.

Great product. Easy install. Fast shipping

Good product. Pricey for what it is, but this isn't all that surprising for a one-time purchase product. Bought this for use with a trash can slider (Rev-A-Shelf RV-18KD-18C S Double 35 Quart Sliding Pull Out Kitchen Cabinet Waste Bin), and installed both at the same time to ensure alignment would be right. Install was a piece of cake and didn't take any longer than suggested in the instructions, maybe less. No problems with the wood screws or double-sided sticky tape others have mentioned. Some have mentioned that it was a problem that the door brackets extended beyond the cabinet frame - this is not a problem as long as your door covers the brackets, and it will not interfere with the door closing all the way. I made one minor adjustment to the door brackets to adjust for tilt top to bottom - I did this even before I put the door on because I could see the angle would otherwise be wrong. Stuck the door on with the tape and made one more minor adjustment for height (I actually did this by unsticking the door and resticking - the tape was strong enough that I actually had a little difficulty unsticking it). And done. Works perfectly. I would only suggest one improvement to the instructions, which is that you'll need a small wrench or plier to hold the stop-nuts which you screw on the L-brackets - a small plier would be best based on the slider frame that, in this case, will otherwise get in the way.

Works exactly as intended but it was a little tricky to install solo. Definitely recommend having a second person - once the cabinet door is lined up you'll secure it with the provided double sided sticky pads, but then you'll have to drill the wood screws into the door. The door wasn't quite secure enough on just those pads to apply the pressure needed to drill into the door - once I had someone holding the door steady, it was no problem getting the screws in place. It functions exactly as intended and I am overall pleased with the purchase.

Exactly as advertised. Installation was a breeze -- I like to think I'm a "DIYer", but in reality I tend to start about twice as many projects as I actually finish (okay, my wife might say it's more like 3-5x as many projects, heh). The only difficult part was getting the alignment perfect, and that was easily solved: just a little bit of patience, 60 seconds of assistance from the wife, and use of the [perfectly thought out] double-sided tape to temporarily hold things in place before screwing it down. The only complaint I have: I managed to break a few of the included screws that go into the cabinet itself but that was easily solved with a few spare screws from around the house. I suspect that this was just a result of our cabinets being oak & a bit on the thicker side, and Rev-A-Shelf trying to make sure the screws are small enough that no one will accidentally puncture their cabinets, and perhaps me torquing a bit too much. ;-) All in all, a *fantastic* addition to our kitchen (no more disgusting trash cans sitting around in the kitchen), very solid & well-made, and at a surprisingly low price given the high quality -- especially compared to having a custom trashcan area added via the "custom cabinetry" route which can cost many hundreds more than the cost of this project!! Wish we'd done it & bought this years ago!!! HIGHLY RECOMMENDED!!

Worked well with adjustments on an existing shelf installed. Due to the widths, I had to create a wooden frame to tie into and therefore needed another set of holes. It was tough to drill through the plates, but it all worked.

Used it for a 35qt installation. It is solid and was easy to assemble and adjust on the doors.

Buen acabado pero no se adapto a mis necesidades, con relación a los insumos empleados en la fabricación, el precio si se me hace excesivo.

I highly recommend this accessory! I love being able to pull open my garbage/recycling cupboard. Well made and sturdy!

Works well. Cheaper to buy this and the garbage can kit instead of the whole kit

La descripción es confusa, yo pensé que era toda la parrilla y solo es el kit de instalación. El cual son 4 placas y tornillos. De hecho no la use.

Works perfectly with trash cans of same brand