CableMod Vertical PCI-e Bracket (Black, 2 x DisplayPort)

First off, this product is worth the money if you want to vertical mount your GPU. There is one major feature that I feel sets it apart from the competition and makes it worthwhile. That said, it is not without its problems.First, the good. The product is quite sturdy and stable. There are some reviews calling it flimsy, but they are being unfair. The unassembled pieces do flex and twist, but you cannot evaluate stability on a disassembled product. Once properly assembled, the mount is very sturdy, and exhibits little to no flex or deformability. Next, The mounting position gives the card plenty of room to breath, so the mounting position does not negatively impact thermals. In fact, it improves the GPU core and hotspot temps a few degrees under load in my testing. Finally, the big feature that sets it apart from the competition is the cables. The cables have a flat, 90-degree connector that when combined with the depth, allows the cables to pass through the rear of the case with no modification. I did have to bend the crossbeams of one of the slots out a bit to create some room, but I was able to bend it right back after the connectors went through. And while it's not specific to this product, the bonus of vertical mounting means making clean, attractive runs with your power cables much easier.Now to the negatives, which I feel are significant, but not deal-breaking. The first negative that you will quickly notice is that the gap between the back of the case and the back of the mount is not filled or covered. It is just open and is hugely jarring and unattractive. I found that a piece of foam packing material that was inside the package was the perfect width and height to fill the gap perfectly, so I just cut to length and jammed it in. It's an inelegant solution, but it works. The other big issue is that no matter what I did, I could not get it to sit perfectly straight. The mount tilts slightly outward as you move toward the front of the case. It's slight, and isn't obvious unless you are looking for it, but it's there, and there is no way to get rid of it. The case itself may be a factor, but CableMods should have known different cases would fit slightly differently and provided a method to adjust the angle of the lower mount to compensate. Finally, I would be remiss if I didn't mention that the cable is PCIe 3.0, so if you have a PCIe 4.0 GPU and motherboard, you will need to go into your UEFI settings and set the PCIe slot to gen 3 or you will get crashes. While it does cause you to lose a very small amount of performance (1-2% in most benchmarks), I've found that the improved thermals more than make up for it. You can always replace the riser cable with a 4.0 cable, but I don't think the extra money is worth it.So, is this the bracket you should get? If you don't have crossbars between the slots on your case, you may do well to get a different brand, but this one is just fine, and gets my recommendation as long as you understand the issues and limitation.

1st one sold as new. box was already opened. plastic latch damaged. returned.replacement was sealed in box. working just fine. bit stiff, made me concerned I was going to damage it. you can tell the latches on these are fragile. recommend an ultra low profile screw driver or very small handle screw driver to fasten below that latch.works fine on my EVGA 3080ti FTW3. just had to make sure i installed the riser cable where the PCB on the 90 degree side was mounted on top of the bottom bracket of my cablemod vertical mount. NOT from underneath. I know it doesn't look good but once everything is installed you can't see it.

Okay so ordered this thinking okay I'll give it a go, wanted something to help showcase the rgb on the fan side of the gpu while still being able to get that pcie 4 performance so i ordered the bracket/pcie 4 cable kit it came with 2 90-degree angle display 2.1 cables. It would have gotten 5 stars however it was not made know that it only came with 2 of the necessary cables and did not include any right-angle HDMI 2 cables. Ended up ordering separately from another manufacturer... kind of a missed opportunity to not include that as well it would even be worth the increase in price by 15-20 to include that as well.....Solid quality parts, all mounting hardware and screws needed for the bracket, good machining there wasnt any additional case modification needed, temperature differential is within 1-2 degrees celsius..... the nitpickiness over the cable is just based on the beginner experience have a little more transparency with exactly what you get or do not..... I held off reviewing this until it was installed in my pc for a month or 2 so i could gauge and test..... not disappointed another really decent consumer product put out by a solid company with good customer service and RMA procedures

There were pros and cons. Unfortunately this item did not work for my build.As seen in the photo, I have bottom case fans, and this did not play well with that.Pros:Mount is thick.The mount also gives you the option to use the bottom support of the bracket instead of forcing you to. The bottom bracket has holes for better airflow, I wish all GPU mounts had holes.Cons:The mount is too bulky and pushed forward, causing the issue of not being able to use with bottom case fans, meaning at minimum you would have to remove one fan.The bottom bracket sits to low on the mount so even if you do remove one fan, the bracket isn’t high enough to sit atop the other to fans.The bracket itself being optional, is held in by two small screws causing GPU sag if you use it.Conclusion:I have a Lian Li O-11 Dynamic case which is made for max airflow, hence why you want 3 fans at the bottom. Most likely your bottom fans are RGB meaning you spent a pretty penny on them and don’t want to have to remove any, not only for airflow but also aesthetic purposes. This mount does NOT work well with Lian Li O-11 Dynamic if you are using 3 bottom case fans, thus I had to refund this item.Side note:If you are like me, using this case with 9 total fans, and want a vertical GPU, go for the Phanteks Veritcal GPU mount. It’s smaller, sturdy, no sag, work with this case AND bottom case fans, and half the cost. Also sold here on Amazon.

Bueno, instalar este aparato dentro de tu ordenador es difícil y tiene desventajas con las que tienes que contar. Eso sí, al menos en teoría, te permite instalarlo en cualquier ordenador con 7 bahías traseras. Incluye lo necesario y trae unas instrucciones que te recomiendo seguir con cautela.** Diseño y producto **Bueno, el diseño es lo que ves, realmente lo único que es realmente es una plataforma metálica y un riser del pci para poder extender el conector al soporte vertical. Aunque es de metal, es maleable, así que te recomiendo que no juegues demasiado con él. Una vez instalado todo bien. Te viene con unos cables de vídeo que son LOS QUE TIENES QUE USAR, sí o sí, debido a la propia construcción de tu caja de del invento este.** Instalación **La verdad es que es un poco infierno instalarlo. Además de seguir con cuidado las instrucciones, si eres de los que, como yo, tienes un sistema de cables ya configurado que pasan bajo los muebles con bridas y todo eso, vas a tener que desmontarlo todo para poner los cables que te traen porque son los únicos que se van a adaptar bien. Y, no sólo eso.El cable de vídeo NO puede ser desconectado del ordenador sin desinstalar la gráfica del soporte vertical. Así que si tienes un sistema de cableado custom (como ya dije antes) y no quieres desmontar la gráfica para sacar el cable, te toca deshacer el cableado entero cada vez que quieras mover por el motivo que sea el ordenador de sitio porque sólo le vale ese cable, ahora es como si el cable fuera una parte más de la caja de tu ordenador y la única solución que veo es coger una sierra y cargarte las bahías y limarlas luego para poder usar tus propios cables o simplemente para poder desconectarlo con normalidad...Si estás dispuesto a aceptar esas condiciones y su precio, cumple su función perfectamente, que es la de poner la GPU en una muy estable posición vertical.Conclusión:Si no tienes otra manera de poner tu gráfica en vertical y quieres hacerlo sí o sí sin ponerte a moddear tu caja, ésta es la opción, pero a un precio (sobre todo el precio de no poder usar tus cables y perder movilidad, más que lo que cuesta).

My case is the NZXT 510.  I bought this kit because it mounts my gpu as far back from the glass to give maximum airflow with this case.  Bracket quality is thick steel with a flat black powder coat finish.  Instructions are online only and pictures are of an older version of the product, but still very easy to follow.  There is one hdmi extension with the special angle plugin to the card.  The DP cable however is NOT an extension but an actual 8ft cable, the cables are of the best quality as well.  Installation is easy just remember to not aggressively bend the supplied riser cable.  Once assembled and screwed into place the card is solid and will not move or sag.----Things to think about before buying this product ----Be aware of the install and the type of card you are using.  The kit will extend about an inch and a half to the length of the card installed due to the cage that holds the special cables, so check to see how much space you have to make sure it will fit in your case.This product takes up SEVEN slots in the case, and with my case that is all of my slots!  If you have any PCI-e cards ie. sound card, capture card, streaming card, or dual gpu's this will NOT work.Overall, expectations all met and shipping was super fast. Pictures attached to show what I am babbling about.

Habe das Teil eigentlich bestellt, um meine neue AORUS RTX3060 Ti aufrecht in ein Corsair Carbide 540Air einzubauen. Also rein physikalisch passt das noch. Leider ist das aber schon alles. Denn die Karte funktioniert so nicht.--- Material/Verarbeitung --- :Hatte das Set mit 2 Display-Port-Kabeln bestellt. Die sind ganz gut. Genauso wie das Riserkabel. Diese Teile machen einen wertigen Eindruck.Der Rest ist halt normales, schwarz lackiertes Stahlblech. Auch zusammengebaut und außerhalb des Gehäuses macht das einen etwas wackeligen Eindruck. Aber das führt nicht dazu, das die Karte dann irgendwie locker im Gehäuse drinsteckt. Das Konstrukt hat eingebaut und angeschraubt durchaus ordentlich Stabilität.--- Einbau ---:Ist im Grunde recht einfach. Man muß aber einiges bedenken.Die Karte sollte man vor Einbau in das Gehäuse auf den Adapter bauen. Dabei den Stromstecker und das Displaykabel nicht vergessen. Und dann am besten direkt den PCIe-Stecker ins Board einstecken.--- Funktion ---:Hatte es zuerst mit meiner alten RTX2060 Xtreme versucht. Das funktioniert einwandfrei und ohne jegliche Probleme. Sieht auch super aus und es wackelt nichts.Dann habe ich es mit der RTX3060 Ti probiert... Und leider war dann nur das ungesunde Piepen vom POST zu hören. Display bliebt schwarz. Habe noch alle Kabel geprüft und konntekein Problem feststellen. Schade eigentlich, denn die Karte sieht halt so eingebaut wesentlich besser aus.--- Nicht ganz so gut ---:Da waren jetzt so spezielle DP-Kabel dabei, die man nur direkt an den Monitor anschließen kann. Kürzerer Adapter mit Buchse wäre mir da lieber gewesen. Zudem muß man die Slotblenden schon verbiegen um das Kabelda durchführen zu können. Bei der RTX3060 Ti kam noch erschwerend hinzu, das die ohnehin schon lange Karte noch mal 3cm mehr Platz braucht. Gut, das ich noch den vorderen Gehäuse-Lüfter ausbauen konnte, sonsthatte es nicht ins Gehäuse gepasst.--- Fazit ---:Kabel sind wertig. Der Rahmen Durchschnitt, aber ausreichend stabil. Funktion ist leider offenbar nicht bei jeder Karte gegeben.Board ist bei mir ein Intel Z590. Ggf. macht das auch Probleme. Oder eben die Kombination.Ist mir aber auch egal, das Teil schicke ich zurück. Ach so, war ein Warehouse-Deal. An sich sehr gut, weil auch entsprechend günstiger. Aber leider fehlten hier 3 Schrauben :(Insgesamt schade, Idee ist gut und sieht einfach cooler aus, wenn man die Karte vertikal einbauen kann.

Title says it all .... no riser cable useless

The kit is super easy to install and fits in nicely once you remove all the PCI brackets from the back of your case. It positions the card a couple of cm from the brackets and provides an angled DP cable and angled HDMI pass-through so that you don't have to saw off the bracket rails on the back of your case, keeping everything intact. The PCI raiser cable is sturdy with limited flex but, you will have to bend it to hide it behind the gpu so that everthing looks neat.The kit does suffer from gpu sag and I think the 2 retention screws CableMod provides to secure the gpu are way to small for the job. Would prefer to use normal thumbscrews as there is a bit of wobble when screwed in.If you are going to buy this, make sure you have enough length in your VGA power cables because you will have to loop them behind the gpu, again for aesthetic reasons. If they have enough flex, they should tuck nicely behind the gpu so only the connectors are visible.Also, shout out to Overclockers.co.uk who sold me this kit on Amazon. Delivery date was scheduled between the 7th and 10th of June and the package arrived on the 4th!