DIY-MotoShield Pro Premium Precut Ceramic Window Tint for 2-Door Truck - Front 2 Sides + Rear Window [99% Infrared Heat Reduction/Blocks 99% UV]

Although the product is very nice and durable, it is not very easy to apply for a beginner! I would strongly suggest you get the extra piece to practice on!

This is a high quality tint and the cuts are near perfect. I would definitely buy this product again because it saved alot of time.However, be careful with the shrinking process on the edges. Side windows went great becausenot much shrinking was required, but had difficulty with rear window on my 2022 Camry. I only shrunk one window previously in my lifetime and I started from the middle and worked my way out to the edges. This worked great when the tint was not pre-cut. Because of the pre-cut, when I heated the edges, they melted quickly and curled up. I got pretty bad creases on my back window because of it. I think the best process may be to tack the edges down first and then heat shrink working towards the middle. Ill probably end up re-tinting my back window at a later date.

This is NOT any sort of high-tech window film. (It is NOT ceramic, and it is of questionable quality all-around.) This is run-of-the-mill stuff ... just as difficult to use as any other cheap window film. The rear window film in my order had "punch outs" in an oval/triangular-ish shape that were cut about an inch from the edge of the film for defroster connections and WERE PLACED INCORRECTLY, making it UNUSABLE. The pics show the gap on the left side defroster connection that remained when the right side defroster punch-out (other pic) was placed flush - even cheating toward the left a bit to try to make it work. IT WOULD HAVE BEEN BETTER IF THESE PUNCH-OUTS WERE NOT IN THE FILM AT ALL. The outside edges were OK, but the misplaced, pre-cut punch-outs made the whole rear window UNUSABLE. In addition, 2 of the other 7 pre-cut windows were too wide in the non-shrinking direction and therefore not usable without lots of shaving in the short time after the film was placed on the window. The SOMEWHAT QUESTIONABLE ADHESION of this film makes this difficult to deal with. If you have a window where extra film cannot be tucked into the rubber around the window - or where there are plastic/metal hardware and/or defroster connections, you need the pre-cut to be exact. THESE CUTS ARE NOT EXACT. If you trust that the cuts are exact, then you may not be prepared to shave the excess within the time required to get it to adhere properly to the window. (Now you know. Fore-warned is fore-armed.). For complex windows, DO NOT USE THE PRE-CUTS AT ALL. You would be better off purchasing a sheet of film and cutting it yourself. The pre-cut for my back window was foolishly placed right in the middle of entire sheet of film - wasting most of it. If it had been placed at the top or bottom of the sheet, I would have had enough left over to cut it myself and re-do the window correctly.

Adhesive appears to be holding great so far after a couple months, the cut and fit was perfect in my case and installation was fairly easy with the rights tools.Heat rejection is nowhere near what I expected, and the color has faded considerably considering its been about half a summer (see the pics).The first thing I noticed after installing is the hazyness. Its almost difficult to see out of it when the sun is hitting it, unfortunately Ill have to find something else to use, its a shame considering the cost.

Easy to install and fits good.

Nothing to complain about everything to love

I want to start by saying I don't ever leave product reviews good or bad on Amazon, if I buy something and it works....good it should. But this product has been so incredible, I want to tell everyone about it, especially after seeing some of the negative reviews from a year or two ago. Most of the negative reviews were related to poor customer service and not sure if they changed operations, but for me their service was great. They contacted me to confirm a detail I wasn't clear on my order form before shipping and appreciated their attention to detail. I also asked a question before having it installed and they answered right away. So as far as service they get 5 stars for me.For the tint itself, it arrived in a very strong and durable tube, nicely packaged. The color and clarity have been perfect but this heat reduction it provides is where their magic is at. I have had other brands that promise UV and heat reduction and some of the more expensive tints worked better than others, but my friend's testimony to this feature piqued my interest. I was skeptical at such a low price for ceramic tint but after only 1 weekend of using it, during 90 degree sunny summer days during this heatwave we've had, I can say this tint is the REAL DEAL.I will preface this review by saying I didn't install the tint myself. It didn't seem too difficult once opened but after saving money on the tint itself compared to what I paid in the past at tint shops, I had a 3rd party mobile tint person do it which ran me around $120 with tip, well worth it to save me the time. I asked him his thoughts on the tint as this his daily business and he said the precut was great and wanted to know what company it was so I passed him their info.All in all, I am happy my friend recommended this brand to me and its safe to say I'll be telling everyone I know with a new car to invest in this product.