关于我们

客户服务

客户支持

区域访问

法律与政策

社会的

获取应用程序

将相机对准即可下载应用程序

Customer support

We're available 24/7 to help you!

daier 24V 6S 40A 18650 Li-ion Lipolymer battery BMS PCB Balance for ebike ebicycle

Q: is there a specific order that wires need to be soldered to the board? Mains first then balanced leads for example?

Assuming the wires are not connected to anything on the other end (aka your battery holder is empty and you have no load or charger connected ) you should be fine with any order. I would recommend moving from one side of the board to the other so you don't concentrate too much heat in one place. Try not to unsolder the pads from the board by applying to much heat. Don't solder live wires!

Q: Where does the charging lead connect?

Not answering the question, but my BMS had the same issue! No voltage/current at P+/P- when everything else is wired up!

Q: can anyone tell me how to connect to the load? do I use p+ and p-?

Initially it was not clear to me where the charge and where the load connected. Other reviews clarified that the both the charger and the load connect to the P+ and P-. The BMS auto switches between input and output depending on the voltage on P+P-. I tested it on my Power wheels car and the full 20 plus volts were on the (P+P=) output terminals. With the charger connected for couple hours it raised the voltage from 3.6 to 3.8. One cell was at 4.0v . I will leave it on the charger overnight and see if it balances better. If you connect your load to B+B= , it will work but you will not have any load overcurrent or under voltage protection for your battery pack. You would be able to run your device till the battery is totally dead, which damages l-ion cells.

Q: Can I wire two of these in series to make a 12s?

Yes, you probably could, but just be aware of the fact that if the BMS is unhappy with the 18650's that you have attached, it will shut down, so you're adding more points of failure by wiring two in series. I actually struggled with this 6S BMS for a while, and nearly gave up on it, because it kept shutting down, until I realized that the resistance of some of my cells was too high. After re-grading all my cells and culling the highest resistance cells, the BMS was able to stay up.

4.0/5

产品编号: 388596675

安全交易

细节

Brand
daier
Battery Cell Composition
Lithium Ion
Recommended Uses For Product
Bicycle
Unit Count
1.0 Count
Voltage
24 Volts

经常一起购买

daier 24V 6S 40A 18650 Li-ion Lipolymer Battery BMS PCB Balance for ebike ebicycle

200mm(7.9in) Width PVC Heat Shrink Wrap Tube 18650 21700 26650 Lithium Battery DIY Battery Pack 3M(9.9ft) Length Blue

MatchWhiz Flat Width 5.9in(150mm) PVC Heat Shrink Wrap Tube for 18650 21700 Lithium Battery DIY Battery Packs Blue Length 9.9ft (3m)

描述

daier 24V 6S 40A 18650 Li-ion Lipolymer battery BMS PCB Balance for ebike ebicycle

is there a specific order that wires need to be soldered to the board? Mains first then balanced leads for example?

Where does the charging lead connect?

can anyone tell me how to connect to the load? do I use p+ and p-?

Can I wire two of these in series to make a 12s?

常见问题

TrustPilot

TrustScore 4.5 | 7,300多个评论

阿里·H.

发货快，包装精良。Leatherman 工具手感非常高档和坚固。

1天前

哈立德 Z.

从订购到送货的体验都很棒。强烈推荐！

1 周前

查看所有TrustPiLot评论

全球购物，通过 Desertcart 享受优惠

物有所值

各种产品的价格具有竞争力

全球购物

为 200 多个国家/地区的 3 亿多购物者提供服务

增强保护

深受全球购物者喜爱的值得信赖的支付方式

客户保证

深受全球购物者喜爱的值得信赖的支付方式。

沙漠车应用程序

随时随地随时随地购物。

NT$1042

关税和税费包括

Taiwan店铺

免费退货

30天对于 PRO 会员用户

15天无会员资格

安全交易

TrustPilot

TrustScore 4.5 | 7,300多个评论

Ayesha M.

产品与描述完全相符。对我的购买非常满意。

5天前

法蒂玛 A.

我尝试过的最好的国际运输。物有所值！

3天前

查看所有TrustPiLot评论