Silk Blue PLA Filament 1.75mm 3D Printer Filament 1KG Shiny Cyan PLA 3D Printing Material CC3D Shine Silky Shiny Metallic Metal Light Blue PLA Filament

This review is for the rainbow gradient silk pla.This rainbow is a bit different than others. It tends to run darker colors and more gold tones. Basically no red, green, or pinks. Two of the gold tones print very similar even though they look very different on the spool. This makes it come out as long stretches of gold (see the deep sea diver model pic). If you like gold, like I do, this isn't really an issue. You can expect most of your prints to include at least some gold coloring. This spool looks like it has so many colors but really you just get 3 main colors and then very gradual transitions that look smooth.:: A rich sapphire blue, a burgundy-ish copper, and gold. Of which there are multiple slightly different gold tones varying from yellow, orange, a coffee, and copper ish.The sool colors can be deceiving. It's surprising seeing what looks like a light eggplant color filament print as a distinct gold color. But you will see this happening with these colors. I'm not sure why the printed colors change so much from the way the color looks on the roll. But it does.I really like the colors but be aware you will find a lot of gold in the mix compared to the blue and purple. And that it will be tricky to predict what the filament will look like when printed.As for quality. No complaints. Printed fine. Wound neatly. I typically bump the nozzle and bed temp for silk. these were all printed at 205c and 70c bed. I sometimes get bed adhesion problems if I use 60c. So if you have such issues, try bumping the bed temp. And make sure bed is clean.

Prints very nice. I’m using it in Bambu X1 and P1 printers. Generic PLA setting. I’ve also printed on .4 and .6 nozzles. Really neat copper color, and I haven’t had any issues with it.

Very shiny prints, beautiful colors. The transition happen a bit faster than expected, but the cross section of the print and volume of infill have a huge impact on that. Smaller cross sections will allow a more gradual color change.The prints I have done are beautiful and the people loved the colors.

These are the best gold and silver silks I've found, that is they look the most realistic. They foam quite a bit which is normal for silk, but it leads me to believe the TPU content is high. For that reason, this stuff really performs best when dried. in fact, it will start to degrade after just 10-20 hours of printing, so I print straight from the dryer. Also, I have had rolls of gold that are less metallic (more like other brands) while I have had many that look exceptionally like real gold. I wish the consistency was better. Printability is just fine on my Prusa Mk3, MK4 and Bambu X1c as long as it's dry. Try going a little slower if you have issues. Layer adhesion is better than other brands I've tried, but it's still a weak point. Orient your print so that layers are perpendicular to the axis you most require strength on. That said, this is for aesthetic parts, not functional ones, so it's more than adequate. Great stuff once you get used to the quirks. I've had parts pass for real metal until handled.

I had been wanting to try one of these mega-gold filaments for a while, so I decided to google around looking for "the best". Everyone has their own idea of what that means of course, but I had to start *somewhere*, and this stuff did come with some decent recommendations, so I figured "what the hell, it's worth a shot", and bought a spool.I've never printed with "silky" filament before, let alone this brand, so it's new territory for me. This stuff is inexpensive ($19.99/kg at the moment), made in China, and people were talking it up, and everyone knows how THAT usually goes -- "if sounds too good to be true, it probably is". I figured if it doesn't stack-up, it won't be a huge loss.At first, I had jamming problems, intermittent starved lines, brittleness, bad overhangs, ooze... the works. So, I didn't get a very good first impression of it. I figured, well, if I can't get this to print nicely, maybe I can just get it going barely well enough to use it for things where it's okay for the part to look ugly or where the color won't matter.But... I didn't want to settle for that, and kept poking at my settings until I finally got it figured out. Over the course of about 20 meters' worth of filament printing calibration objects, I got it dialed-in decently, and all those issues just... went away. Afterward, I printed a couple of small non-calibration items, then put the spool away for the time being. I still have some fine-tuning to do before printing anything big or important, but that's to be expected when playing around with a new filament, and it was already past time to shut things down for the night.So, yeah... that first impression was wrong. I mean, dead, fracking wrong! This really is a good product. As I wrote in the headline, the photos I saw didn't lie, and I'm certain mine don't either. It really does look as nice as the claims.One of the defining properties of this stuff: between the overall glossy/shiny/silky appearance and the way light interacts with the texture of the printed surface, it's hard to see the layer lines on flat vertical or curvy/"organic" surfaces (like the side of a cube, or the hull of a Benchy), making prints look a lot smoother than normal. At least, at 0.2mm layer height, anyways. Of course, mechanically, the layer lines are no different from any other plastic. This effect doesn't hide the "terraced terrain" look of gently-sloping top/bottom surfaces (like the Benchy's gunwale or cabin roof), but as with any other filament, you can mitigate that to some degree by using a finer layer height where it's needed, or maybe with that non-planar slicing method that's making the rounds.This leads to another nice quality: it's slick to the touch, even coming from my old printer (which doesn't produce the smoothest of surfaces to begin with). In fact, it almost feels "oily", compared to my other filaments. Of course, it's probably just as dry as any other plastic. It's simply *that* smooth right out of the hotend. I now wonder what vapor smoothing would do to it (and what solvent one would need for this product, for that matter).One thing that surprised me is that this stuff wants (in fact, demands) a lot less retract than any of the other filaments I use. As in, they all need around 2 mm of retraction length, while this gold does great with just 0.5 mm). I'm certain that too much retract was what led to jamming, starved lines, and ooze (paradoxically).Now, on the questionable side, this filament does have a LOT of die swell. For those who don't know, this is the effect where extruding into free air too fast (for a given temperature) will cause the extruded plastic to distort, shrinking lengthwise while also getting fatter, not unlike a muscle contracting. Or, as someone else described it, "like a hanging worm reacting to being touched".This isn't too much of a problem during normal printing, though, and can be beneficial in one case: if you anchor a line of hot plastic to something, stretch it across open air, and anchor the far end to something else, then let it cool, the filament's tendency to shrink lengthwise will cause it to pull itself taut between those anchor points (at least, with reasonably thin lines).Of course, we all know that this is how bridging works in 3d printing, and this behavior leads to *great* bridges with very little droop, but it has the negative side effect of making partial overhangs less than ideal, as they'll want to curl up if printed too fast. This is particularly apparent on parts with a small horizontal cross-section, which lead to short layer times, such as the 30-85° overhang test pictured above. The behavior of bridges and overhangs is comparable to ABS, but less severe, and like that material, these issues can be dealt with with appropriate settings or using things like a dwell tower or just adding more parts to the plate, so that there's more to print at heights where the problematic overhangs show up.And...well... it doesn't smell sweet when printing, like PLA normally does. Gotta have that delicious smell of waffles. :-)Also bear in mind, this is a standard-size 1kg spool -- the photo attached to this Amazon listing makes it look bigger than reality.## End of review ##The following settings were used to print most of the items seen in the photos attached to this review (ignore the object on the far left, it's a bad print and is NOT representative):* Hotend: 195°C (precisely calibrated)* Bed: 65°C* Diameter: 1.73 mm* Flow: 94%* Geometry: 0.2 mm layer height, 0.4 mm line width* Speeds: I use Slic3r's autospeed mode, with a 5 mm³/s volumetric flow rate target, which works out to around 70 mm/s on most print moves. Travels at 300 mm/s, and retract and unretract speeds are both set to 40 mm/s. 1000-1500 mm/s² acceleration. X/Y jerk is set to 20.* Cooling: fan at 85% on print moves, 100% on bridges ( I usually run it flat-out 100% at all times on other PLA's, and PETG typically gets 15 to 25% on print moves and 50 to 100% on bridges, depending on color).The printer is just an old acrylic Prusa i3 MK1 clone that I've modded, upgraded, and just generally tinkered with over the years. It is equipped with a genuine RPW-Ultra all-metal hotend, with 12v/40W heater and 0.4 mm nozzle, a direct-feed, geared extruder of my own design, and Printbite-covered glass for the print surface. Layer cooling is provided by a 5015 blower, through a duct that aims the airflow at both the left and right sides of the nozzle. The whole kit is controlled by a BigTreeTech SKR v1.3 loaded-up with TMC2208 driver modules, and running Marlin (bugfix-2.0.x branch).

Silk PLA is probably my favorite material to print; maybe it's just my settings, but it always comes out easily and smoothly. This one (silk purple) was no exception, and turned out some beautiful prints without much work!

Color muy brillante fácil de imprimir sin deformación me gustó mucho!

Prints super nice. Nice shine to it !

As a crafting business owner and jeweler, I am constantly on the lookout for materials that can enhance the quality and aesthetic appeal of our creations. Recently, we had the pleasure of working with Silk Purple PLA Filament CC3D, and it has truly exceeded our expectations in terms of performance and visual impact.First and foremost, the quality of this filament is exceptional. The consistency of the diameter, combined with its smooth texture, ensures reliable and consistent 3D printing results every time. Whether we're crafting intricate jewelry pieces or creating detailed 3D models, Silk Purple PLA Filament CC3D delivers impeccable print quality with crisp details and clean lines.One of the most remarkable features of this filament is its stunning visual appeal. The silky shiny finish of the printed objects gives them a luxurious and elegant look that instantly elevates their perceived value. The rich purple hue adds a touch of sophistication to our creations, making them stand out and catch the eye of our customers.Moreover, Silk Purple PLA Filament CC3D is incredibly versatile and easy to work with. It adheres well to the print bed, minimizing the risk of warping or lifting during the printing process. Additionally, its low tendency to string or blob ensures smooth printing without the need for constant monitoring or adjustments.Another aspect that we appreciate about this filament is its eco-friendliness. Made from PLA, a biodegradable and renewable resource derived from plant-based materials, Silk Purple PLA Filament CC3D allows us to create stunning pieces without harming the environment. This aligns perfectly with our commitment to sustainability and responsible crafting practices.Overall, Silk Purple PLA Filament CC3D has become a staple in our workshop, and we couldn't be happier with the results it delivers. Whether you're a professional crafter or a hobbyist, I highly recommend this filament for anyone looking to add a touch of elegance and quality to their 3D printed creations.

Se imprime tal cual se ve en las fotos, producto de gran calidad, lo he comprado 2 veces.

I’m new to 3d printing and wanted to try some silk PLA for a shiny appearance.I purchased this and have had no problems so far printing with it. Using the recommended settings on the reel it has so far printed well.I have had no clogging or breaking or tangling.I would purchase this again.