GAME | 40mm to 1.5-Inch Pool Hose Adapter Conversion Kit | Pack of 2

Highly recommended deathly fixed a problem

The kit allowed me to connect my Intex brand pool to the non-Intex pump and filter effortlessly. The plastic construction of the adapter made it durable, and the included gasket and o-rings ensured a leak-proof connection. I must admit, it was a relief to avoid the hassle of hard plumbing with PVC, thanks to these handy adapters. Tip: The Teflon tape included in the kit comes in handy for a snug fit and prevents any leaks. Make sure to use it while connecting your hoses! The only slight criticism I have is that it required a bit more plumbing tape than I anticipated to get a leak-proof seal, but it was a small trade-off for the convenience it offered. All in all, I'm thrilled with this conversion kit, and it turned my pool upgrade into a breeze.

i kept trying to figure out why when I bought a new sandfilter/pump combo off amazon why it would suggest this little part. once the pump/filter got here I realized why. i have a intex aboveground hardsided pool, the 1/4 hp pump it came with and 50lb sand filter were clearly not enough to keep up with the filtering so i ordered a 150lb filter with a 1.5hp pump with built in strainer basket. i wanted to keep all the lines that were on the pool still and just hook them up to this new combo but intex has their own size hoses/nut that threads onto their pump and filter. so when i ordered the new stuff none of the hoses i had fit, THIS LITTLE PART HERE THREADS INTO THE PUMP INLET OR FILTER 6WAY VALVE AND ALLOWS YOU TO USE NON INTEX PUMPS/FILTERS WITH YOUR STOCK HOSES. this works great because the intex hoses i like because they are clear and have the built in shut off valve on both sides of the inlet and outlet and i dont want to hard plumb everything with pvc just yet!

I'm running an Intex C2500 pump/filter with a Hayward skimmer on a Polygroup Summer Waves pool. I wanted a LOT of power. The 40mm ends connect well to the Intex hoses, although don't over tighten. They do pop, so there could be a size issue and I just don't see any leaking so I'm good with the fit. And the 1 1/2 end connects perfectly to the Hayward parts. I have since added the Intex Above Ground Plunger Valves between the GAME adapters and the Intex C2500 hoses.

If your hooking up a Hayward skimmer to a Intex pool your going to need this conversion kit because Hayward does not give you the correct adapters. This kit worked perfect and was easy to install. They also give you plumbing tape with the kit. Excellent product.

Fit perfectly in my hayward pool skimmer! We used it to connect a 1 1/2 in hose to our hayward in the wall skimmer and it hooked up great! No leaking! Price was great too!

works great

These adapters do indeed adapt from 1.5 inch to intex thread for using their hoses with more common size hardware. I got them to install a 3 way valve, and they did indeed adapt one to the other. They leak out of the box, however. I can't tell if this is because the thread size is just a bit off or if the included gaskets are just too thin. I think perhaps both contribute to the problem. Typically this type of connection will leak if the compression nut is loose, but trying to tighten them more results in the nut jumping the threads so it will not tighten more. This is because the tolerances are a bit loose and perhaps because the intex hose nut is also plastic and somewhat flexible. I could blame the hoses, but they do not leak when connected to anything else on the pool. One could likely correct the issue by using intex seals, which are thicker, but these adapters aren't shaped correctly to accept the intex seals. If you're handy and you don't have other options, these can be made to work. I put E-6000 on one side of each seal, gluing it to the adapters and once dry I put the same sealant on the opposite side and tightened the hose onto the fitting while the sealant was still wet. This worked for me, but God help me when it's time to take these apart. I also used the same sealant between the 3 way valve and the adapters, as the included o-rings would deform and displace as I tightened them in to seal. This may be because of the shape of the mating surface of the valve is rounded so I'm not knocking them on that. Still, although the threads did fit, none of the included seals or o-rings actually sealed for me and I had to improvise to correct. YMMV. At the end of the day, I did get my valve installed and it only cost me an extra $7 on a tube of sealant.

Bom kit, com tudo incluído necessário para ligar mangueira roscada de 38' a skimmer exteriores da marca hayward e gre 👍

indispensable pour interconnecter le monde INTEX et le reste... ..

Great product if you want to change from Intex or Best way pool fittings to a standard PVC.

Product arrived as described and with very fast delivery. Great seller. Thank you.

Kurz und knapp, gutes Preis-Leistungsverhältnis, verwendetes Material ist okay, sehr passgenau...topp