Universal Reloading Press LED Light Kit – 12 LEDs, 200 Lumens

Sweet little set up. The led strip is quite flexible, so you can mount it to your press in various position. I mounted mine on a loadmaster and it was simple. The light is sterile white and bright. Everything you need to mount is included in the kit. If you are handy you could piece a kit like this together for a bit cheaper, but for the hassle saved, it is a bargain!

My package received less than ideal handling in route to me, and as a result, one of the components was damaged. I contacted KMS Squared, they promptly sent the replacement part, and in no time my system was up and running. KMS Squared provided me with superior customer service after the purchase, and as an Amazon seller, they should serve as the benchmark. The KMS Squared lighting system is a very effective means to illuminate your work area. The simplistic design accommodates a wide variety of applications, while providing economical lighting solutions. Instead of becoming a compromise the hobbyist must contend with, this streamline lighting system, "blends in to become a part of the intended application." This is a "No Compromise" approach to effective lighting solutions! This product adds value to any application where lighting is critical! Universal Reloading Press LED Light; Fits RCBS, Lee, Dillon, Hornady, Lyman etc.

Let me say this is the product I have been waiting for in reloading. Took a break from it 4 years ago and just started again. This was my biggest complaint about the whole process. So what do I find but this LED kit. Installed it on my Load Master and it works very well. I know it says you can trim some of the lights off to fit your needs but there was no way I was going to do that. I just curved the last 2 along the press radius so they shine down a little. Lined the lights up on the left side of the press so the round section of wire at the end of the LED strip did not kink and strapped it down with the included zip tie. You must follow the directions so you get good adhesion on the LED strip. Takes longer to decide on placement that installation. All components appear to be of good quality. Switch works well. Cord length should be good for most people. Overall a very good product.

This system works very well. Easy to set up. Pretty much plug and play. The only issue I had was the adhesive on the back of the light strip was not as tacky as it should have been. It was an easy fix with some double sided tape. Other than that, this product throws a good amount of light as long as you position it properly.

Wanted this to make it easier to visually verify the powder drop on a Lee Classic Turret Press- The LED strip attached to the round support without much issue. I cleaned the support first with Lacquer thinner and then scuffed it with the small included abrasive pad. Then used the alcohol prep pad and allowed the area to dry for about a minute. I peeled the backing from the strip starting at the top and once I had that where i wanted it I continued to peel the backing as I slowly mounted the strip down the support. Zip ties are also included and one at the top and bottom was more than sufficient to help hold it in place. The LED strip is bright and allows easy visual inspection of the inside of the case to see the powder charge- I highly recommend this product to avoid missing a no charge or double charge load- Both of which could have serious consequences.

I have a Hornady AP press. I put a lamp over the press when I operate it but shadows from the lamp make seeing the cartridges a bit difficult. This light strip is very bright an makes it easier to see what I'm doing. Mounting is easy.

Fits and works great on my Lee Classic Turret press. I contacted the Seller with a question and they got back to me in a timely manner. Product is designed to adhere to a flat upright, however the Lee Classic Turret has round uprights. Including some pics I took of the completed install. The light is bright enough to see into a case neck when standing at the press. Great for a final powder check before bullet seating. I used some tool box drawer liner as a backing which really holds the light strip in place on a rounded surface. Secured it with the zip ties supplied (snugly but not too tight). Highly recommended and top marks for the Seller response back to questions!

I received my reloading press light package today Friday, all items accounted for, all looked well made. Plugged all together to test, everything worked. I used the piece of scotch Brite pad to scrub the surface where I was to install lite strip and wire hold downs. Wiped all surfaces with supplied alcohol wipe. Installed lights. Sticky strips are holding just fine. Started reloading twenty minutes later 3 lits out. Now it's Friday night 7:30 pm I emailed kms squared, within 5 min. I had a reply with an appology and a tracking # of a new light strip on the way. That is what I call great service. Very happy and even with 3 lights out, it still is pretty good.I would definitely buy again