45 Degree Offset Rail Mount Picatinny Low Profile Adapter Mount Laser Light Rail Attachment Red Dot Optic Iron Sight Mount fit keltec sub 2000

Exactly as described, the fit is perfect and allows the carbine to fold with the optic installed. One note: the set screws to lock the mount to the rail are tiny and it took a little time to find the correct bit that was small enough to fit the screws. It does not come with the allen key.

Excellent fit for Sub2000. BUT....BUT...i still had an issue with my scope. The rifle cant be closed with the scope attached. Im trying to solve this problem and will add an update when i do.

I'm another person that used this for his SUB 2K. It was very easy to install, but I was concerned that it would damage my guns polymer picatinny and/or it might eventually work loose because the two set screws tighten up against the edge of the guns polymer picatinny rail. That's not the fault of this mount of course. If the rail were aluminum then there would be no issue. My work around was to grind down a thin piece of metal approximately two inches long and an eighth of an inch wide and insert it between the set screws and the picatinny rail on the gun. Then I could sufficiently tighten the screws without damaging the picatinny rail. I used thread locker so the set screws don't back out. The issue I had was when I mounted my little Sight Mark. The sight mounts on it's own base plate and that base mounts to this little offset mount. I found the base attached just fine, but it was too wide which made it difficult to properly collapse the rifle. I tried several bases with the same issue. My solution here was to grind down one side of the base plate. I sprayed the ground down edge of the base plate with four or five coats of black paint, put it all together and now my SUB could properly fold. If the little picatinny rail on this offset mount stuck out just an eighth of an inch more then this wouldn't have been a problem. As it is, I'm happy with the results. This little offset mount is plenty strong and solidly attaches to the weapon. An aluminum picatinny would not have the problem I had. I like this solution for adding a red dot reflex sight to the SUB 2K much better than the much more expensive Midwest Industries swivel mount I had been using previously. Smaller, less weight, it doesn't block the guns sights and no action is required by me to move the red dot out of the way in order to open or fold the rifle. I actually find holding the SUB at an angle to shoot to be more comfortable somehow.

So far it works great. Hoping it it stays solid. set screws seem a little small but it is tight right now. Will check after shooting a few rounds. Used to offset a red dot sight for a daylight/backup on my night vision AR.

I like the low profile but the attachment interface could be designed better. It works on some rails but not others if they're slightly narrower since the set screws are angled and can't make up width differences. Pretty much every other form of picatinny mount works horizontally to account for these slight dimensional discrepancies. The Monstrum brand picatinny rail on our Ruger 10/22 was too narrow for this mount, and it would just fall off. I got it to hold by applying a layer of fairly thick duct tape on each side of the rail to widen the interface. This should work fine for my purpose since I only need it to hold a small light, but I wouldn't trust it with optics.

It does what i need it to do. Running it with a a 1-4 single focal plane sight. Does get in the way of the sight passed 1x. Probably wouldn’t show if I ran it one notch back but it doesn’t bother me. >After shooting Highly suggest using blue lock tight. I highly recommend even though it was meant for airsoft it isn’t a functional part of the rifle so it doesn’t affect the most important cycles of the weapon. 4 stars for sturdiness because without lock tight you’re gonna lose a lock bolt.

Where to begin? - First of all, the way that mounts doesn't work.it uses 2 set screws but even if tightened all the way down it does not fit snug and tight. It is loose. No way this will work. I am mounting it on a KelTek sub 2000 and this is advertised to fit it. - Second, I like the low profile nature of it. The gun will fold and latch with it installed. Unfortunately, once you put a sight on it forget it. And if it won't do that then what is the point of this attachment? - Third, the offset is not 45 degrees, rather it is more like 30. This is why it does not have enough clearance to close. I was really hoping that a low cost item like this would save me from buying the $150 Mcarbo product that flips out of the way but I guess there is no getting around that. I am returning this product and I do not recommend it to anyone.

Outstanding fit and function. Perfect for the job. Allows the PCC to fold as designed. Great value, easy install

work great

If buying for a sub 2000 if fits nicely on but the second you try to mount something on the 45 rail and fold the sub2000 there is no clearance and whatever you mounted will hit the stock.

Made well, easy to install, price point is reasonable. That's why I ordered a 2nd one and never received it. So, if you can get one, excellent but look at getting from another venue ...

i bought it for my kel tec sub 2000. it initially fits, but then i tried to put my bushnell trs-25 red dot on, and then there is no clearance to collapse by a mm. then i had to buy a feyachi riser to raise the view profile a bit and now it BARELY FITS when collapsed but still touches the buffer tube. it also has tiny set screws that mar the piccatiny rail when tightened, doesn't seem stable.

Didn't fit couldn't return.