Model no.: S0112 # Rapid Push Button Detachable Swivels. Easy to install, and versatile. Flush-mount front and rear bases for stud-free profile when sling and swivels are removed. Bases glue in place, no screws required. Fit 1" Sling. Package: Swivel + Screw Studs Details pls. kindly refer to product picture with spec.
A**Y
Would be great...
One of the sling mounts came locked in and I couldn’t get it open. For the one that worked as expected, it works great. Sling mount locks in and stays in pretty good. Unfortunately the mount that is stuck, pops out pretty easy. Nice set if they were both working properly.
S**Y
Fits Magpul but bad swivels.
The main reason I purchased these is just to get the retaining cups for my Magpul X22 Backpacker stock on my 10/22 TD. I already had purchased 2 Jialitte 1.25" QD swivels and cups and they fit great and the swivels where the size I needed. I just purchased these so that I could attatch my sling to either side of the rifle. I figured, since these where cheaper, the cups looked the same, and a different size, I could have multiple options for a sling. Unfortunately, the swivels are difficult to remove. They are not anything I would use to attach a sling to my rifle. You have to really push the button down and jiggle it to get them to release. Lucky for me, I don't plan on using the swivels. And the cups fit the Magpul stock nicely. If that is your plan, they will work. Otherwise I would be returning them.And keep in mind that they do not come with any hardware to attach them. I use aluminum Chicago binding posts because they have a thin head that will allow the swivel to properly seat on either side. But I have to put them in a drill and take a file to them to get them small enough to fit inside the cups. It only takes about 2 minutes to do both sides of both screws. Magpul charges $15 for each retaining cup. These are slightly different, but work great.
B**.
Fits a KE Arms KP-15
Used to mount on a KE Arms polymer lower stock fit like it was made for it. Sandwiched the two together in the stock and used a Chicago screw with lock tight to hold it in. It worked out far better than I hoped ! I now have QD mounts on both sides of the stock that work and look a lot better than the unfinished holes left by KE Arms! All in all much cheaper than the single side kit KE sells.
G**A
oversized QD swivels
The quick detach swivels work just fine with the female inserts supplied...but the actual diameter of the swivel will not fit into any other QD slots on existing attach points on rifles or camera lens foot... too big. Would not purchase again.. quality is not issue... just size mismatch
T**D
Nice to have, I think.
These installed easily on my Ruger 10/22 Takedown so I could break it down and put the parts back in the case without the sling attached. But they are very hard to release with my arthritic fingers. It takes a lot of force on a small button to get them to come off.
J**D
$49.95 vs $12.72
like
A**R
Trust but Verify!!
Price is great when you consider that Magpul charges an outrageous amount ($14) for just the female part, HOWEVER, before mounting the female part in your gun aggressively try to pull the male and female parts apart without touching the release button. If you can pull them apart they are defective, send them back and try again. One pair worked fine for me the other was defective. You definitely want to know this before trusting your expensive rifle to a defective part.
G**.
Beware
Note that there is no hardware included to mount the QD cup to the buttstock. They expect you to glue it in place. This is ridiculous and not a secure method to hold the cup in the cup socket of the stock. When (not if) the glue fails, your rifle will hit the ground.
T**H
Buy these for the sockets.
I purchased these for my Magpul SGA stock. The QD sockets are 100% awesome. Your sling will spin 360° in this, in case that's an issue. I used a little JB weld to make real sure the sockets stayed put in my stock.The sling loops that come with the sockets are odd. They work with these sockets just fine, but are REALLY tight in other standard QD sockets. So keep that in mind.Other than the loops being a slight bit out of spec, and for how little these cost, if you're looking to add QD functionality to your Pew, get these.
A**R
Fits SGA stocks!
These fit the Magpul SGA stocks perfectly.I decided to use a small amount of epoxy to fix them n place. It works fine.The fit and finish on them is not quite up to Magpul standards (they're a little stiff and rough) but they work fine and they're half the cost of Magpul.
P**M
Sling Swivel 1.0 Inch with Push Button Quick Release Detachable and Tactical Sling Mount
the QD push button is too small/too short to push down to release. After a few pushed, finger was hurting. I would never buy that again.
C**3
Ok, not great but cheap
The QD sling doesn’t remove very easy from the base . The button is small and difficult to push.Does the trick for budget item but not great
G**N
QD rings, one of the two did not clip. Sent them back and re-ordered a new set
Utilisé pour les ceintures de carabine.
Trustpilot
3 weeks ago
3 weeks ago