CURT 13322 Class 3 Trailer Hitch, 2-Inch Receiver, Round Tube Frame, Compatible with Select Chevrolet Silverado, GMC Sierra 1500, 2500 , Black

High quality and easy to put on.

fit perfectly on a 2011 chevy Silverado 1500 extended cab 6.5 bed.... 2 bolts on this hitch VS The OEM had 3. OEM was poor design. this hitch is a nice heavy duty steel.. Pulling a 30 ft camper, Forest river. so strong!!! well made !!!

Apparently Curt has read the reviews! I noticed is the reviews I read prior to purchasing that many people had an issue locating the hardware that comes with the hitch. Apparently they would wrap it up inside the receiver and now it is shrink wrapped to the tube beside the receiver so you cannot miss it. I also read that many wound arrive with scratches and dings. Mine was nicely packaged in a box with cushioning. Fit perfectly and was an easy install by myself. Lined the hitch up under the truck on a floor Jack with the receiver on the jack pad and jacked it into position loosely installed the bumper bolts. Then was able to align the other holes and install remaining hardware. Then tighten opposing bolts until all were tightly in place.

Hasn't fallen off or broke yet and have had it on there for a long time and it has been used and abused pretty easily to install

Purchased to replace a rusted out receiver on a 2013 silverado 1500. A few things to note: The box was destroyed during shipping but the product was fine. A few minor scratches didn't bother me at all. The fit was perfect. I had no issues bolting the new one in place and had no gap between the bumper bolts and receiver as others mentioned. The replacement receiver, in my opinion, is not nearly as good as the OE part. There are 2 bolts on each side vs. 3 on the original. The OE part is braced on both sides of the mounting bolts vs 1 side on the replacement. The OE mounting brackets are significantly longer. The angled holes for the safety chain on the OE receiver are easier to use than the flat holes on the replacement. I can get the chains latched into the new receiver but it's more difficult with the receiver pin in place. The new hitch sits closer to the bumper than the original on my truck. It made my enclosed single axel 5x10 work trailer sit a little too high with the 2" drop I had previously used. I tow a trailer daily. If my truck didn't have 310,000 miles I'd probably have spent more for the OE part but this seems like a decent product for the price if you're doing light occasional towing. It looks fine and doesn't jump out as being aftermarket. I dropped the spare. You don't have to. Takes about an hour. The original hardware is better. Mine was fine so I reused it.

Worked great for my 2009 gmc 1500! Thanks again!

Replaced the rotten hitch on my 2004 Silverado. Fits perfectly, now I can tow safely again. My only small issue, there is no bracket for the trailer light plug.

Excellent product nice welding job and definitely sturdy. Install was very easy on my 2010 GMC sierra.

Excellent quality. Fit perfectly.

Me llegó en 2 días desde Estados Unidos, esta excelente muy buen producto

Purchased this hitch for my 2011 GMC Sierra. Everything was as detailed in the instructions. Very straight forward, all necessary hardware was included. Just depends on your location, my truck has some rust I needed to deal with first to get 2 bolts out and 2 new ones in. But that's not the fault of the hitch. Took about 45 min to install alone. Works as expected and is hidden nicely with no interference to the spare tire. Thanks.

I am happy with it so far. I think I may drill two tiny (1/16" or 1/8" holes possibly with welded reinforcement around them) in the bottom of the receiver to allow water/condensate to drain from the lower portion of the receiver; thus minimizing the rate of internal corrosion. The holes would allow me to spray corrosion inhibitor (i.e. Fluid Film) into the lower portion periodically. Or, I may weld steel plates over the open ends of the receiver to prevent moisture, road salt or chemicals placed on the roads in the winter from entering. My old receiver with open ends (original from the dealership) had failed due to internal corrosion (was able to shove 4 fingers through the receiver pipe at the low point; an accident waiting to happen.

Looks like descent quality Customer didn’t give all the info needed So ordered the wrong hitch Needed one for a 2500hd Cost to send it back was almost as much as what it cost + the restocking fee So were going to modify it to fit Not sellers fault