Automotive Authority LLC Narrow 0.6" RV Marine Camper Vinyl Insert Trim Mold Screw Cover (White, 25 ft)

This strip didn’t produce quite the same “pooching out” of my original strip. The result was a bit flatter when installed. (It’s possible I needed a slightly wider version). Nonetheless it looks great, given that the originals were broken, mildewed, or missing altogether.It was quite difficult to install, which is expected. Patience, perseverance, and some sore thumbs later, it looked great. Maybe there is a magical formula for installation but I was relegated to aligning one side of the groove and pushing in the other side with a flat blade screwdriver, a half inch at a time. Also had to roll/rub/beat the installed strip to make sure it fully seated.

This screw cover is far superior to the original product that was on my camper. The original was stiff and brittle. Yes it was old, but the design was not well thought out. This stuff is tough to put into the small track if you have arthritis and you're not very coordinated. This is 1/16 wider than the track making a tight fit. Which is good because it's flexible and will bow out in the middle where the screw heads are. If it wasn't wider the screws would push the trim out and the wind would catch it and it would end up on the highway. But that tight fit made it hard for me to install. A putty knife helped and using the handle end of a screwdriver to push it in helped. Take your time and you will get it done. Great stuff. Only complaint is you get too much. I bought 50 ft because I have 2 exterior doors. Have over ten feet left that will likely got to waist. Rv doors are standard sized normally. Selling the right length would prevent waste. This wasn't cheap.

The plastic screw channel covers on my screen door were cracked and finding replacements was a test of my patience. The channels were 1/2" W and the width on this seemed close enough (.62").Worked great. Took another reviewers suggestion and left it out in the sun to soften. Went in like a charm. Just used a putty knife and worked my way down. Because it is a little wider than my channel, it bowed out slightly.Being vinyl I know this will shrink slightly in cold weather so the fact that it is .62" will probably be good.But looks great. Took the paint to match my door well too.

Very good fit laid in there. Perfect not hard to put in. Good quality.

Took a year to find a good replacement for the lost trim around our RV door (came off somewhere on an 8 hour trip). Dealership admits this is a common issue, didn't have any trim in stock. They offered to order some at 2.40 per FOOT!!This replacement is about twice as thick as the original (and less than half the cost!) This makes for a tight fit, but it looks great, and has no chance of coming off during the drive.Material appears to be of high quality, and is pliable even in ~50 degree temps. It fit snug into the groove, and conformed to the tight ~4 inch radii in the corners of the door without any buckling or sign of distress.Overall, a great buy, much better alternative than the overpriced replacement.

Putting it in the slot was slow going with a hair dryer. The heat gun made it a breeze by softening it 2 feet at a time. Looks great.

I have a vintage 1975 Six-Pac camper. The front window molding was very faded and brittle. Ordered this molding and could not be happier. Fits perfectly and looks great. Now my only Dilemma is it looks so good, I am going to change all the molding. Thanks for such a great product.

The product is good but a bit stiffer

This product is rubber and very flexible, the old stuff i was replacing was weathered vinyl cracked and a mess.this product fit perfectly I am so pleased because bayliner as big as they are could not help

Tried to clean the rub rail in our boat … wouldn’t come clean. Carefully measured before buying this online. Worked like a charm! Old boat looks new again!

The narrow 0.6 RV trim mould will not fit into sharp curves. It buckles and falls out of curves because it is too inflexible.

I’ve included before and after of a compartment on my rv. I read that if you leave it out in the sun it softens and goes in the grooves easier. I still used a butter knife to guide in some places! Super happy and ordered more to do the rest.

Fit my storage compartment door and generator door on my 2013 Dutchman Toyhauler. Let the material warm in the sun before installing.