ITBEBE 100-Pack Pass Through Cat6 RJ45 Connectors and 100-Pieces Red Strain Relief Boots for 24 AWG Cables

I'll keep this short. After battling with installing just one connector for over an hour, I decided to try one of my standard connectors to see if it was just me. Nope. No problem with my regular connector. The problem is that these are for a smaller gauge wire, so you have to push real hard just to get it to go through the connector. This obviously bends the wires and makes your efforts fruitless. So, unless you are using a gauge smaller than 23, you'll be disappointed. Lesson learned. Caveat emptor.

They are easy to work with but when you are done they WILL NOT LOCK IN TO PC, LAPTOP OR ROUTER. I cable end with or without the blue cover stay in the ethernet receiver. They just fall out. Nice looking cable but use have to use duck tape to keep it plugged in.UPDATE: ITBEBE got back with me about the problem and has given me a full refund. They said they were sorry for the problem but they stand behind they product. Good people to deal with!!!

I make many patch cords at my work. I use almost any brand on the market and give a try. I make few patch cords with itbebe connector, but this gold-plated connector is better than other connectors I used.This jar has 50 connectors and 50 strain relief. This connector and strain relief is the perfect set for patch cord making.I use Itbebe crimp tool to make this patch cord. This gold plated connector has 3 prongs. A conventional connector has 2 prongs. 3 prong is better than 2 prongs. 3 prongs have better conduct than 2 prongs.I untwist the cable and make it straight for easy pass-through to the front. I make all the untwist cables as the same size for easy pass through to the front. I use same itbebe cutter to cut the excess front wires.Once all the wire in and out to the front, I twist it and secure it. I push the connector to the rj45 crimp tool. I press and hold the connector to the crimping tools rj45 hole then press. This process will crimp and trim same time for my RJ45 patch cord.I made over 20 patch cords. Each patch cord was perfect for my network

Using my tools I got 90% error rate for the cat 6 cables I crimped with these connectors. The connectors are advertised to be gold plated, however the ones I received had silver color...The Cable Strain Relief part is GREAT though.

I love the fact I can tread the wires as whole and just crimp it cuts and I'm done.... Only issue I have it the boots only work with normal cable not outdoor rated cable like I'm using the boots will not work.. but the connectors work flawlessly!But under normal cat5e/6 the boots will work!

This was my first time using pass through connectors. There's a lot of different ones out there, I didn't know which ones to get. So I just tried these ones and they worked good. The holes are big enough to let the real copper wires go through. I needed to make cables for POE cameras so it was very important that the holes were big enough for the thicker real copper wires. I think the Ethernet cable I got was 23 gauge direct burial double wrapped but yeah they worked fine with no problems. I didn't use the sleeves, it gets crowded quick on the back of the NVR so I didn't use them.

This product is a great value. For a novice it makes manufacturing cables a lot easier. Using the right heads with the right cable, bundled with a good pass through crimped makes the work easy.I had only one issue with cracking a lock on one of the heads. I will own that as I should have laid the cable and put the heads on afterwards, but it was easier doing it the other way. I think It got caught when I was fishing the line... Aside from that one head, all the others worked great with good quality on signal. - Best of luck

I got these along with a roll of cable for my new house so I could run Cat6 everywhere for computers and TV's. The ends fit the cable perfect and connections are solid. So far no issues.

These pul-through RJ45 plugs make terminating cables so much easier and less error-prone. These particular plugs come with strain reliefs too which one can either use or not depending on the use of the cable. For patch cables I use them but for fixed ones, they're not really necessary in my view. Al in all though an excellent product and the jar they come makes storage very easy too!

CHEAP plastic connectors and even worse sleeves. What I liked in the description is that the 8 wires run straight through the connector (that is quite easy to make sure they are in the right order) which would be cut when you crimp. Well it crimps but does not cut through the 8 wires requiring me to trim them with a stanley knife. It kind of works, but is not as advertised. Maybe this is due to the cat5 cable I use, but still... For what they are, it is expensive and I will not buy again.

I bought these based on the reviews of other people but when they arrived I was disappointed with the quality of the item. The plastic is brittle, has sharp edges, burrs and overall the quality of the finish is poor. I tried 2 different thickness of cables and each one was a struggle to get in the connector. I've tried 6 or 7 now and each time it strips the wires and the internal guides are so useless the wires are stripped, crossed over or both.I generally recommend products and try to find the positive sides but I cannot recommend these to others unless you have incredibly thin cables.

Really professional product. I bought these along with the corresponding Itbebe crimping tool. So simple, yet 100% effective and professional. Fantastic quality, worth spending the extra money.HIGHLY RECOMMENDED!!

Really easy to use and check as the wire passed through the plug so you know it's right before crimping. Haven't got the right crimp tool to cut the overhang wires but a craft knife does the job.