Siraya TechSimple Water Washable 3D Printer Resin - Low Odor, Easy to Print, High Precision 405nm LCD UV-Curing Aqua Resin - Ideal for 8K Capable LCD, DLP 3D Printers (Grey, 1kg)

I really feel I am getting the best prints I have ever gotten out of my Elegoo Mars. I am also able to trim down the exposure time by .5-1 second, depending on the layer thickness, so that speeds up printing for me. It cleans up really easy, but I think 15% alcohol might be a bit conservative.And due to a super low viscosity, it drains off really well when you let your build palte sit at an angle for a while to drain off excess resin. I go with a 50% alcohol mix, swish around in bath 1 for about 20 seconds, then move to bath 2 for a 20 second swish and it is cleaned perfectly. I find I do not have to brush or scrub any areas to remove any resin. It really does help extend the life of my alcohol with the clean draining and lower % alcohol needed.I am not really looking to print much at all in a translucent black/grey, so I add just a bit of any other type of white or grey resin to the bottle, just enough to make it a bit more opaque and this works great. This may slightly affect the alcohol % to clean, but not enough to worry about. I keep to a slightly short post-print cure so my pieces are not super brittle and I am really happy with the results I get.The only caution I have is your printed piece will be very susceptible to moisture damage, so do not overly soak your piece, this also applies even after curing, so do not also excess moisture to collect. Painting with usual acrylic paints is no issue and it paints up great.

I am a first time user of resin printing. Had about 5 years of FDM printing prior to this. My new setup is the Anycubic Photon Mono X, with the Wash And Cure machine. Cleaned in 90% isopropyl alcohol, which is what I had at the time. I will try the 17% isopropyl alcohol later, to test the products claim. The prints were downloaded from Thingiverse, sliced in Lychee with auto supports generated. My first experience with anything resin. So I'd say the result of first 2 prints are amazing from this resin. I am satisfied and will probably buy more of this brand since there lots of good reviews. There are some other brands that are priced a bit lower, but I wanted to have a positive experience with my first resin printer.

Post-processing was a breeze, with just a quick swish in ipa and a rinse under the faucet. Gave the print a good shake and wipe down and ran over it with a hair dryer for good measure. Put into my UV station for about a minute and was done. The color comes out as advertised-a perfect smoky black.What’s more impressive than the low-hassle clean up and post processing, you might ask? The printing speed. It’s not the fastest curing resin I’ve ever used, but what makes it so fast is that the viscosity is so low it’s almost water-like. This enables you to really crank that lift speed and retraction speed without worry, which significantly reduces your print times.

Too transparent, . When the product dripped from above the laser light hardened the liquid that dripped on a previous layer. Wasted 14 hours.

Probably the most beautiful resin I’ve printed with, and very easy to clean. A quick coat of clear gloss varnish after curing helps make printed parts crystal clear. Very little IPA needed to clean.

This stuff is crap, it says non brittle but its more like super brittle. We have tried every thing to get different results if possible and nothing. I hate that we bought two bottles of this crap.

Love this mixes well with other translucent colors. By it self works great too.

2.5 second exposures on a mono 4k printer, very impressed. Definitely a work horse resin.

Super easy to print resin. Good and affordable price. Recommended!

3Dプリンターを使い始めて1年にも満たない初心者ですがSNSなどの評判をみて購入。メーカーが配布しているChitubox用の設定ファイルいじらずそのままで室温約20℃でプリント。消毒用エタノールを15%前後に希釈した水溶液で洗浄→ドライヤーで乾燥→78Wのネイル用LED UVライトで二次硬化という工程を行いました。造形物をノギスで計測して元データと比較したところ0.1mm以下の誤差でプリントできていて驚きました。またエッジもダレることがなくかなりシャープに造形できました。（プリンターはELEGOO Mars2）液体の状態はSK本舗の水洗いレジンと比べて粘度が低くサラサラ。硬化後の色合いはサーフェイサーよりも薄いライトグレーです。15%のアルコールで洗浄可能なため水洗いレジンに準じた使い方ができ、精度も高く、かつ価格も安い、と初心者にもとてもおすすめできるレジンだと思います。