Wireless Bridge with 2 Bracket,2.4G Point to Point Outdoor WiFi Bridge with 3281ft Working Distance,24V POE Power Supply, IP65 Waterproof Internet Bridge,2-Pack

Installed on a shop that is only 30 yards from my house so I can't confirm the max distance. It works perfectly in my situation. I installed a $40.00 Wi-Fi router on the recieving end. Configuration was easy. I watched YouTube videos and followed directions for setup. It basically took a few minutes to configure and it works great For streaming videos, wifi calls, web browsing etc. Highly recommend.

Works great! Easy install and super easy connecting. Internet is very fast!!! Highly Highly Recommend this product. Great value and works even better than advertised!

initially worked well, product failed after 35 days, bridge will not connect, 200 feet away. master unit just continuously cycles with chasing led

Dec 20223 : 2 year use review :This set has worked flawlessly for 2+ years continuously. Been through extreme Central Texas heat, 2 major freezes, heavy rains : & didn't disconnect even once. Just ensure it is mounted very firmly on the pole (or your exterior wall etc - higher up, the better). I am planning on setting this to connect to 2 more 'slaves'. So 1 master supplying internet to 3 slaves. Great for installing security cameras to remote corners of the farm - by using small solar setup.Aug 5, 2021 : (when 1st installed)I needed to bridge 2 houses 1500 feet apart at my farm. It was quite easy and straightforward. Just use the "preconfigured" method, instead of the GUI etc. I used 50 foot CAT6 network cables both sides, to take them up on the roof of the 2 houses.1st, I powered the 2 up in the same room (both next to each other), simultaneously squeezed the RESET button on both - which caused them to pair. When the blinking green light turns solid green - it means they paired successfully.Next - I tested their connection while both still in the same room ... MASTER connected to the Internet Router, and SLAVE connected to my laptop. The Internet was successfully beaming across the 2!!...now came the part of mounting the 2 at top of the two separate houses, 1500 ft apart. Which I did. Made sure the 2 devices faced each other ...though they don't have to PERFECTLY face each other.They easily "connected" at that distance of separation .... took about 2 mins to re-connect, after I reconnected to POE power at the other house.One little drawback to be careful about : the 2 green lights on the side are REALLY DIM. So dim, that when out in the bright daylight, they don't appear lit at all. For a while I thought the devices were not powering up - perhaps due to faulty cable. But then I cupped my hands around the lights and peered in - and saw the light WERE actually lit.At the second house - I connected the LAN output on the small black power/POE adapter - to a WIFI router. So this second house now is fully WIFI Internet connected. Working perfectly.One little 'trick' I used - that I believed helped get a stronger signal. I had an old "leftover" dish antenna on top of the second house. I turned it around to face the MASTER house, and placed the SLAVE device at the focal point of the dish.

all good, little trouble pairing ! but got it

I wanted internet in a detached garage without running buried cable. This product is one of several I considered. For the money, I decided to get this.Here’s what I think each person should know before buying it:1. Instructions are terrible, the company knows it and say they are working on improving them but, maybe I should go ahead and make a YouTube video they can use. What? No.2. The power is provided for each unit by a wall wart type plug that accepts Ethernet cables. One is for power and data to the unit so make sure your cable is capable of PoE. The other cable goes from the plug to the router.3. The unit at the house which goes to the modem for your internet service is considered the “Master” and the switch is set to AP from the manufacturer. Check that before mounting it to save yourself some hassles. The other unit is the STA setting for “slave” or “station”. This is the unit on the out building.4. There are no mounts.5. Disregard the 12V power plug inside the unit, you don’t need it, it’s not supported and you wouldn’t want to use it because that would mean having AC near each unit.6. There is a small reset button inside the unit that also selects different channels to use. Make sure each unit is on the same channel.7. If both lights on the unit are illuminated and NOT blinking the units are paired.8. These should be plug and play. If it doesn’t work you probably don’t have them paired correctly, have the AP/STA switches backwards or have a bad cable.These were a pain to get working because the company has terrible directions. The company did send a prompt reply via email support but by then I had it working.Hassle up front but now clear and fast internet in the shop.

Works great. My span between the two houses is approximately 1/2 mile. Very easy to setup and install. If you have Starlink V2 you need a special cable (photo). AmazonTo hook up P.O.E power adapter

Got sent an open/used product.Judging by the writing in the manual, the previous person had not had much luck.Other than that, product works fine. If you mess with tech frequently, setup is logical. The paperwork is typical chinese affair.